How Much Extra Material to Buy: A Waste Allowance Guide
The area you measure is never quite the amount you need. Cuts, breakages, settling and the odd mistake all eat into your materials. Buy too little and you pay for a second delivery — or end up with mismatched batches. Buy far too much and money sits in the garage. Here are sensible waste allowances for common materials, and why they differ.
Waste allowances at a glance
| Material | Typical extra | Why |
|---|---|---|
| Concrete | 5–10% | Uneven ground, spillage, concrete left in the mixer |
| Gravel, crushed stone, sub-base | 10–20% | Compaction — the stone packs down when rolled |
| Mulch and bark | 0–10% | Settles a little after watering |
| Topsoil | 10–20% | Settles when firmed and watered |
| Flooring, straight lay | 5–10% | Cuts at walls and doorways |
| Flooring, diagonal or herringbone | 15–20% | Many angled cuts |
| Tiles, straight grid | 10% | Edge cuts and breakages |
| Tiles, diagonal or herringbone | 15–20% | More cuts; large tiles are costly to break |
| Drywall / plasterboard | 10–15% | Offcuts around doors and windows, damaged corners |
| Decking boards | 10% (15% diagonal) | End cuts, knots and splits |
| Roof shingles or tiles | 10% gable, 15% hip | Cuts at hips, valleys and edges |
| Bricks | 5–10% | Cut bricks and breakages |
| Paint | Round up to whole tins | Coverage varies; keep leftovers for touch-ups |
| Wallpaper | Strip method + 1 spare roll | Pattern matching wastes length on every strip |
Most CalcBrook calculators have a waste setting with these defaults (paint and wallpaper round up to whole tins and rolls instead), so you can see the effect before you buy.
Why some materials need more
Layout and pattern
The biggest driver of waste is how many pieces you cut. A floor laid in straight rows only loses a strip at each wall. Lay the same planks diagonally and every row starts and ends with an angled cut; herringbone multiplies that again. The same is true for tiles, and for decking laid at an angle.
Size of the room
Small rooms waste proportionally more than large ones, because the cuts at the edges are a bigger share of the area. A large open-plan floor might need only 5%; a small bathroom with a toilet, basin and bath to cut around can need 15% even for a straight layout.
Compaction and settling
Loose materials shrink. A cubic yard of crusher run or MOT Type 1 makes noticeably less than a cubic yard once a plate compactor has been over it — which is why sub-bases need 10–20% extra. Topsoil settles when it is firmed and watered, so a raised bed filled exactly to the top will sink below it after a few weeks.
Concrete: never run short
Running out of concrete mid-pour leaves a “cold joint” — a weak line where fresh concrete meets concrete that has started to set. Order 5–10% extra and have a plan for any leftover (a few fence-post holes or a small pad), rather than risking the slab.
Why buying it all at once matters
- Batches differ. Tiles, flooring, paint, wallpaper and bricks vary slightly in colour between production runs. Check that batch or shade numbers match on every box.
- Ranges are discontinued. A spare box of flooring or tiles is the only reliable way to repair damage in five years’ time.
- Delivery costs add up. A second delivery of gravel or concrete can cost more than the extra material you would have ordered.
When to buy less
If your store takes back unopened boxes, buying generously and returning the surplus is low-risk. If it doesn’t — special orders, bulk aggregates, ready-mix concrete, tinted paint — stick closer to the lower end of the range and measure carefully. How to measure a room walks through accurate measuring.
Example: the same room, two layouts
A 15 × 12 ft living room is 180 ft². With laminate laid straight (10% waste) you need 198 ft² — 10 boxes of 20 ft². Laid diagonally (15%) you need 207 ft² — 11 boxes. In metric, a 4 × 3.5 m room (14 m²) needs 15.4 m² straight or 16.1 m² diagonally: 8 or 9 packs of 2 m². The flooring calculator lets you switch layouts and compare.