Plaster Calculator

Work out how many bags of finishing plaster or undercoat plaster you need to skim or plaster a room, from the wall area and the thickness of the coat.

Calculate plaster for walls and ceilings

Measure by
ft m
ft m
ft m
ft² m²
Total area to leave out
in mm
Skim: 2 mm (about 5⁄64 in)
%

Results

How to use the plaster calculator

  1. Enter the room’s length, width and wall height, and the total area of doors and windows — or switch to “Total area” and enter the area directly.
  2. Choose the plaster: a finish (skim) coat, or an undercoat for bare masonry or uneven walls.
  3. Check the thickness. The standard figures are filled in for you; increase it for uneven walls.
  4. Keep about 10% extra. Plaster that has started to set cannot be re-mixed, so some waste is unavoidable.

Replastering from bare brick or block needs both an undercoat and a finish coat: run the calculator once for each.

How plaster is calculated

Wall area = 2 × (length + width) × height − doors and windows Plaster = area × thickness × weight per m² per mm × (1 + waste) Bags = plaster ÷ bag weight, rounded up

PlasterUsual thicknesskg per m² at that thicknessCoverage of a 25 kg bag
Finish / skim coat 2 mm 2.5 10 m²
Undercoat – bonding coat 11 mm 9.1 2.75 m²
Undercoat – hardwall 11 mm 8.3 3 m²

These figures come from manufacturers’ stated coverage for gypsum plasters. Coverage varies with the surface and the plasterer, so treat the bag count as a close estimate and check the bag you buy.

Worked example (UK)

A 4 × 3.5 m room with 2.4 m walls has 36 m² of wall. Taking off 3.5 m² for a door and window leaves 32.5 m². A 2 mm skim uses 2.5 kg per m²: 81 kg, or 89 kg with 10% extra — 4 bags of 25 kg. The same walls in an 11 mm bonding coat would need 325 kg: 13 bags.

Worked example (US)

A 14 × 12 ft room with 8 ft walls has 416 ft² of wall, or 376 ft² after taking off 40 ft² of openings. A finish coat about 5⁄64 in (0.08 in) thick uses about 0.52 lb per ft²: 215 lb with 10% extra — 5 bags of 50 lb, each covering roughly 96 ft².

Before you start

  • Check the date on the bag. Gypsum plaster has a shelf life of a few months and sets too fast when old. Buy it fresh and store it dry, off the floor.
  • Mix with clean, cold water in a clean bucket. Traces of old set plaster make a new mix go off quickly.
  • Mix a bag at a time, or less. Finishing plaster stays workable for roughly an hour and a half; a beginner will cover far less than a bag in that time.
  • Boarding first? The drywall and plasterboard calculator works out the sheets, and the paint calculator the paint once the plaster is dry.

Frequently asked questions

How much area does a 25 kg bag of plaster cover?

A 25 kg bag of finishing plaster covers about 10 m² at the usual 2 mm skim thickness. Undercoat plasters go on much thicker: a 25 kg bag of bonding coat covers about 2.75 m² at 11 mm, and hardwall about 3 m² at 11 mm. Coverage halves if you double the thickness.

How thick should a skim coat be?

About 2 mm (roughly 5⁄64 in), applied as two thin coats one after the other. Undercoat plaster is normally 11 mm on walls and 8 mm on ceilings, followed by the 2 mm finish. Trying to fill deep hollows with finishing plaster leads to cracking — level them with undercoat or filler first.

What is the difference between bonding coat and hardwall?

Both are undercoat plasters. Bonding coat is for smooth, low-suction surfaces such as concrete, painted walls treated with a bonding agent, and plasterboard. Hardwall is for masonry that absorbs water — brick and medium-density block — and is tougher once set. Neither is a finish: both are skimmed over.

Can I skim over old plaster or painted walls?

Yes, if the old surface is sound. Remove loose or hollow patches, wash off grease, and apply a bonding agent first — PVA adhesive diluted as directed, or a grit-based bonding primer on glossy paint — so the new plaster sticks and does not dry too fast.

How do I skim coat a wall in the US?

Plaster skimming as done in the UK is uncommon in the US, where walls are usually drywall finished with joint compound. A “skim coat” there means a thin layer of joint compound over the whole wall, or veneer plaster over blueboard. This calculator works for gypsum plasters by weight and thickness; for joint compound, use the coverage printed on the bucket.

How long does plaster take to dry before painting?

A skim coat on plasterboard typically dries in 3–7 days; thicker undercoat work can take 2–4 weeks. It is ready when it has turned an even pale pink with no dark patches. Start with a thinned “mist coat” of emulsion (latex) paint so the paint soaks in and bonds.

Built by Paras Garg and checked by Shivam Sharma and Muskan Gupta. Formulas and figures last reviewed on . Results are estimates: product yields vary, so check manufacturer labels and local building rules before you buy or build. Spotted an error? Tell us.