Firewood Calculator

Measure a stack of logs in cords, face cords or cubic metres, and see how much heat it holds for your wood species and stove — and what that heat costs.

Measure a stack of firewood

ft m
ft m
in cm
%
Open fireplace: 10–25%
$ £

Results

How to use the firewood calculator

  1. Stack the logs neatly and measure the length and height of the stack.
  2. Enter the log length and how many rows deep the stack is. A full cord is three rows of 16-inch logs, 4 ft high and 8 ft long.
  3. Choose the wood and your stove’s efficiency to see how much heat the stack will give.
  4. Enter what you paid to see the cost of that heat — and compare it with gas, oil or electricity.

How firewood is measured

Stacked volume = length × height × log length × rows Cords = stacked volume ÷ 128 ft³ (3.62 m³) Face cords = length × height ÷ 32 ft² Heat = stacked volume × 0.66 × wood density × 4.1 kWh/kg

About two-thirds (0.66) of a neat stack is solid wood. Seasoned wood at 20% moisture holds about 4.1 kWh of heat per kilogram (6,350 BTU per pound) whatever the species, so the heat in a stack depends on how dense the wood is. Loose-tipped logs take up about 1.4 times their stacked volume.

Worked example (US)

A stack 8 ft long and 4 ft high of 16-inch logs is 42.7 ft³: one face cord, or ⅓ of a full cord. In seasoned oak that holds about 8 million BTU. Burned in a 75% efficient stove it gives about 6 million BTU of useful heat — as much as roughly 1,765 kWh of electric heating.

Worked example (UK)

A stack 2 m long and 1.2 m high of 25 cm logs is 0.6 m³ stacked (about 0.84 m³ as loose-tipped logs). In seasoned oak that weighs about 285 kg and holds 1,170 kWh. A 75% efficient stove turns that into about 877 kWh of heat in the room.

Heat by wood species

Wood (seasoned)Density, kg/m³Million BTU per cordkWh per stacked m³
Oak72024.11950
Hickory81527.32210
Beech72024.11950
Maple (hard / sugar)70523.61910
Ash67022.41810
Birch65021.81760
Larch59019.71600
Cherry58019.41570
Douglas fir51017.11380
Pine48016.11300
Spruce43014.41160
Poplar / aspen42014.11140

Figures are for wood at about 20% moisture and are within about 10% of published firewood tables. Wet wood gives far less: much of its heat goes into boiling off the water, and it makes more smoke and creosote.

Buying firewood

  • US: firewood is sold by the cord or a fraction of a cord. Terms like “truckload”, “rick” and “face cord” are not fixed volumes — ask for the stacked dimensions and log length, then check them here.
  • UK: logs are usually sold by the loose cubic metre or bulk bag. In England, wood sold in volumes under 2 m³ must carry the “Ready to Burn” mark, certifying 20% moisture or less.
  • Kiln-dried logs cost more but are ready to burn straight away. Seasoned and “green” logs are cheaper but may need drying at home.

To compare the cost of wood heat with other fuels, see the heating cost calculator; to find how much heat a room needs, use the BTU calculator.

Frequently asked questions

How much wood is in a cord?

A full cord is a neatly stacked pile measuring 4 ft high × 4 ft deep × 8 ft long — 128 cubic feet, or about 3.62 m³. That volume includes the air between the logs; roughly two-thirds of it is solid wood. A cord of seasoned oak weighs around 3,800 lb (1,720 kg).

What is a face cord or rick of wood?

A face cord (or rick) is a stack 4 ft high and 8 ft long, but only one log deep. With the usual 16-inch logs it is one-third of a full cord; with 12-inch logs, a quarter; with 24-inch logs, half. Always ask the log length when comparing prices.

How many cords of wood do I need for winter?

For occasional evening and weekend fires, 1–2 cords lasts most US households a winter; in the UK, 3–5 m³ of loose logs is typical for a stove used the same way. Heating a whole house with a wood stove in a cold climate typically takes 3–6 cords, depending on the size and insulation of the home. A cord of seasoned oak in a 75% efficient stove gives about 18 million BTU (5,300 kWh) of useful heat.

Which firewood gives the most heat?

By volume, dense hardwoods: hickory, oak, beech and hard maple give 24–27 million BTU per cord, against 14–17 million for pine, spruce and poplar. By weight, all dry wood gives about the same heat — softwood simply burns faster, so you need a bigger pile. Dryness matters more than species.

How long does firewood take to season?

Split softwood needs about 6–12 months, and dense hardwoods such as oak 1–2 years, stacked off the ground with the top covered and the sides open. Wood is ready at 20% moisture or less. See how to season and store firewood.

Built by Paras Garg and checked by Shivam Sharma and Muskan Gupta. Formulas and figures last reviewed on . Results are estimates: product yields vary, so check manufacturer labels and local building rules before you buy or build. Spotted an error? Tell us.