Concrete Steps Calculator

Work out how much concrete you need for a flight of solid outdoor steps — with a normal top step, a deeper landing, or leading up to an existing porch — in cubic yards or cubic metres, and how many bags of mix to buy.

Calculate concrete for your steps

Count the risers
in cm
in cm
ft m
in cm
Blank = same as a tread; 0 = existing porch
%
$ £

Results

How to use the concrete steps calculator

  1. Enter the number of steps — that is, the number of risers you step up. If you only know the total height, the stair calculator splits it into equal risers.
  2. Enter the height of each riser, the depth of each tread and the width of the flight.
  3. Leave the top landing blank for a plain flight, enter a larger depth for a landing outside a door, or enter 0 if the steps lead up to an existing porch or deck.
  4. Keep 10% extra and read off the volume and the bags of concrete mix.

The concrete steps formula

Solid steps are cast on the ground, so each step is a block that reaches all the way down. Counting from the bottom, step 1 is one riser high, step 2 is two risers high, and so on. The top step (or landing) is full height.

Lower steps = width × riser × tread × (1 + 2 + … + (steps − 1)) Top step = width × (riser × steps) × landing depth Volume = (lower steps + top step) × (1 + waste %)

With no separate landing, the top step is just another tread and the whole flight simplifies to width × riser × tread × steps × (steps + 1) ÷ 2. Bags are counted the same way as in the concrete calculator: about 0.60 ft³ per 80 lb bag, or roughly 2,136 kg of dry mix per m³.

Worked example (US)

Three steps 4 ft wide, with 7 in risers and 11 in treads: 4 × (7 ÷ 12) × (11 ÷ 12) × 3 × 4 ÷ 2 = 12.8 ft³. With 10% extra that is 14.1 ft³, or 0.52 yd³ — 24 × 80 lb bags (32 × 60 lb or 48 × 40 lb). The steps rise 21 in in total and run 33 in from front to back.

Worked example (UK)

Three steps 1.2 m wide, with 170 mm risers and 300 mm treads: 1.2 × 0.17 × 0.30 × 6 = 0.367 m³, or 0.40 m³ with 10% extra. That is 35 × 25 kg bags or 44 × 20 kg bags of concrete mix — at this size, mixing your own from cement and ballast is usually cheaper, and the concrete mix ratio calculator shows the quantities.

Step sizes that are comfortable and legal

USUK
Comfortable riser6–7 in150–180 mm
Comfortable tread11–16 in280–400 mm
Code limits (homes)Riser up to 7¾ in, tread at least 10 in (IRC)2 × rise + going between 550 and 700 mm (Approved Document K, England)
Landing at a doorAt least 36 in deep (IRC)Check Building Regulations for your project

Local codes vary and change, so check with your building department or building control before you build steps to a door, and fit a handrail where it is required.

Building tips

  • Slope each tread slightly — about ⅛ in per foot (1:100) — towards the front, so rain runs off rather than freezing on the step.
  • Give the steps a footing or a compacted base so they do not settle away from the house. In cold regions, footings go below the frost line.
  • Use a strong mix and keep the concrete damp for several days while it cures; steps take more wear and frost than a slab.
  • Reinforce larger flights with rebar or mesh — the rebar calculator helps with the steel.

Frequently asked questions

How much concrete do I need for 3 steps?

Three steps 4 ft wide with 7 in risers and 11 in treads need about 12.8 ft³ (0.48 yd³) of concrete — around 22 × 80 lb bags, or 24 with 10% extra. In metric, three steps 1.2 m wide with 170 mm risers and 300 mm treads need about 0.37 m³.

How do I calculate concrete for steps?

Treat each step as a solid block that runs down to the ground: the bottom step is one riser high, the next is two risers high, and so on. Add the blocks together: width × riser × tread × (1 + 2 + 3 …), then add the top step or landing at its own depth.

What size should outdoor concrete steps be?

Comfortable outdoor steps are usually 6–7 in (150–180 mm) high with treads of 11–16 in (280–400 mm). US codes based on the IRC allow risers up to 7¾ in and treads from 10 in; in England, Approved Document K asks for twice the rise plus the going to be between 550 and 700 mm. Keep every step the same height.

What if the steps lead up to an existing porch or deck?

Enter 0 for the top landing depth. The calculator then leaves out the top step, because the porch or deck itself is the final step.

How can I use less concrete in a big set of steps?

Fill the core of wide or tall steps with well-compacted hardcore, crushed stone or clean rubble, keeping at least 4 in (100 mm) of concrete over and around it. That can cut the concrete needed by a third or more on larger flights — subtract the fill volume from the total.

Which concrete mix should I use for steps?

Use a strong mix — about 1 : 1½ : 2½ cement, sand and gravel, or 1 : 3½ cement to all-in ballast — or a bagged mix rated for steps and paving. Steps take heavy wear and frost, so they need a stronger mix than a shed base.

Built by Paras Garg and checked by Shivam Sharma and Muskan Gupta. Formulas and figures last reviewed on . Results are estimates: product yields vary, so check manufacturer labels and local building rules before you buy or build. Spotted an error? Tell us.