Decking Calculator

Work out how many deck boards, joists and screws you need for a new deck or decking area — and the total length of board in linear feet or linear metres (lm) — with board gaps and a waste allowance.

Calculate decking materials

ft m
ft m
in mm
Actual width — a 6″ board is 5½″
in mm
ft m
in mm
%
$ £

Results

How to use the decking calculator

  1. Enter the deck’s length in the direction the boards will run, and its width across the boards.
  2. Enter the actual board width (not the nominal size), the gap between boards and the length of boards you will buy.
  3. Enter the joist spacing — 16 in (US) or 400 mm (UK) is typical.
  4. Keep 10% extra for offcuts, knots and splits; use 15% for diagonal or patterned layouts.

How decking is calculated

Rows of boards = deck width ÷ (board width + gap) (rounded up) Board length = rows × deck length × (1 + waste %) Boards = board length ÷ length of one board (rounded up) Linear metres = deck area ÷ (board width + gap), plus waste Joists = deck length ÷ joist spacing + 1 Screws = rows × joists × 2

Worked example (US)

A 16 × 12 ft deck with 5½-inch boards and ⅛-inch gaps: 144 in ÷ 5.625 in = 25.6, so 26 rows. 26 × 16 ft × 1.1 = 458 ft of board — 29 boards of 16 ft. Joists at 16 inches: 13 joists, each 12 ft long, and about 676 screws.

Worked example (UK)

A 4.8 × 3.6 m deck with 144 mm boards and 5 mm gaps: 3,600 ÷ 149 = 24.2, so 25 rows. 25 × 4.8 m × 1.1 = 132 m of board — 28 boards of 4.8 m. Joists at 400 mm centres: 13 joists of 3.6 m, and about 650 screws.

Common board sizes

BoardActual sizeTypical lengths
US 5/4 × 6 decking1 × 5½ in8, 10, 12, 16, 20 ft
US 2 × 61½ × 5½ in8–20 ft
US compositeabout 1 × 5½ in12, 16, 20 ft
UK softwood decking28–32 × 120–144 mm2.4, 3.6, 4.8 m
UK compositeabout 25 × 140–150 mm2.4, 3.6 m

Planning tips

  • Stagger the joints. Where boards meet end to end, make the joint over a joist and stagger joints between neighbouring rows.
  • Choose board lengths that fit. If your deck is 12 ft long, 12 ft boards waste less than 16 ft ones.
  • Keep air moving underneath. Ground-level decks need a weed membrane and some gravel for drainage — see the gravel calculator.
  • Adding steps? Use the stair calculator for the risers and stringers.
  • Finishing the deck? The stain calculator works out the stain or decking oil for the same area.

Frequently asked questions

How many deck boards do I need for a 16 × 12 deck?

With 5½-inch boards and ⅛-inch gaps running the 16 ft length, you need 26 rows. That is 416 linear feet of board — about 29 boards of 16 ft with 10% extra for cuts and defects.

How far apart should deck joists be?

In the US, joists are usually spaced 16 inches on centre for wood decking laid straight, and 12 inches for diagonal boards or many composite products. In the UK, 400 mm centres is the usual spacing for softwood decking boards. Always follow the board manufacturer’s maximum span.

What gap should I leave between deck boards?

About ⅛–¼ inch (3–6 mm) for most boards, so water drains and the wood can swell. Very wet pressure-treated boards shrink as they dry, so they are often laid tight. Composite boards have a specified gap — check the instructions.

How do I convert m² of decking to linear metres?

Divide 1 by the board width plus the gap, in metres. For 144 mm boards with 5 mm gaps: 1 ÷ 0.149 = 6.71 linear metres (lm) per m² of deck. By area, a 4.8 × 3.6 m (17.28 m²) deck needs about 116 lm; the calculator rounds up to whole rows of boards — 25 rows × 4.8 m = 120 lm, or 132 lm with 10% extra. In feet, 5½-inch boards with ⅛-inch gaps need 2.13 linear feet per ft².

How many screws do I need for decking?

Two screws wherever a board crosses a joist. For a 16 × 12 ft deck with joists at 16 inches, that is about 676 screws. Buy a bit more for mistakes — screws are cheap compared with a second trip.

Does this include the frame and footings?

It gives the number of joists and their length. Beams, posts, footings, ledger boards and joist hangers depend on the height and design of your deck, and raised decks usually need a permit and engineered spans — check local building rules.

Built by Paras Garg and checked by Shivam Sharma and Muskan Gupta. Formulas and figures last reviewed on . Results are estimates: product yields vary, so check manufacturer labels and local building rules before you buy or build. Spotted an error? Tell us.