How to use the stain calculator
- Choose a deck, a fence or any other area, and enter its size. For a fence, choose whether you are treating one side or both.
- Pick the type of product and the state of the wood. Rough-sawn fence boards and old, grey, weathered decking soak up far more than smooth new boards.
- Enter the number of coats. If the tin gives a coverage figure, enter it to replace the typical one.
- Read off the total and the cans or tins to buy. Buy the same batch for the whole job so the colour matches.
Typical coverage per coat
| Product | Smooth wood (first coat) | Rough or weathered (first coat) | Later coats |
|---|---|---|---|
| Semi-transparent or penetrating stain | 250 ft²/gal · 6.1 m²/L | 150 ft²/gal · 3.7 m²/L | About 2× further |
| Solid colour (opaque) stain | 300 ft²/gal · 7.4 m²/L | 200 ft²/gal · 4.9 m²/L | About 1.25× further |
| Fence & shed paint / garden wood treatment | 405 ft²/gal · 10 m²/L | 205 ft²/gal · 5 m²/L | Same as the first |
| Decking oil | 325 ft²/gal · 8 m²/L | 205 ft²/gal · 5 m²/L | Same as the first |
These are cautious mid-range figures from manufacturers’ labels: Behr’s US semi-transparent and solid stains (200–400 ft²/gal for a first coat), Cuprinol Garden Shades (10–12 m²/L on smooth wood, 3–5 m²/L rough sawn), Ronseal One Coat Fence Life (6 m²/L rough sawn) and Cuprinol UV Guard Decking Oil (8 m²/L). The rough-wood figure for decking oil is our own estimate. Your tin’s figure is always the best guide.
How the amount is worked out
Deck area = length × width + extra area Fence area = length × height × sides First coat = area ÷ coverage Later coats = area ÷ (coverage × later-coat factor), for each extra coat Total = first coat + later coats
Penetrating stains soak into bare wood on the first coat, so the second coat goes about twice as far. Film-forming products such as solid stains and garden paints are treated more cautiously: about 1¼ times as far for solid stain, and the same as the first coat for paints and oils.
Worked example (US)
A 16 × 12 ft deck is 192 ft². With a semi-transparent stain on smooth boards, the first coat at 250 ft²/gal takes 0.77 gal and the second coat at 500 ft²/gal takes 0.38 gal: 1.15 gallons in all — buy 1 gallon and 1 quart, or 2 gallons if the stain only comes in gallons.
Worked example (UK)
A 4.8 × 3.6 m deck is 17.3 m². With the same stain (6.1 m²/L first coat), two coats take 2.8 + 1.4 = 4.2 litres — a 2.5 litre tin and two 1 litre tins, or one 5 litre tin, which is often cheaper. For a 15 m run of 1.8 m fence in rough-sawn timber, one side is 27 m²: two coats of fence paint at 5 m²/L need 10.8 litres — two 5 litre tins and a 1 litre tin.
Get the most from every tin
- Test a patch first. The colour on the tin is a guide; wood species and age change it.
- Clean the wood before staining. Dirt, mould and old flaking finish stop stain soaking in and make it wear out early.
- Apply thin coats. Too much penetrating stain sits on the surface, stays sticky and peels.
- Stir, don’t shake, and mix several tins together for a large job so the colour is even.
Our guide on how to stain a deck or fence covers preparation, weather, application and drying times step by step. Building the deck first? The deck calculator counts boards, joists and screws, and the fence calculator works out posts, rails and panels.
Frequently asked questions
How much does a gallon of deck stain cover?
Most semi-transparent deck stains cover about 200–300 ft² per gallon for the first coat on smooth, sound wood, but only about 125–150 ft² on rough or weathered boards. A second coat of a penetrating stain goes roughly twice as far, because the wood is already partly sealed.
How much fence paint do I need for a 6 ft fence panel?
A 6 × 6 ft (1.83 × 1.83 m) panel is about 3.3 m² per side. At 5 m² per litre on rough-sawn wood, that is about 0.7 litres per coat, per side. Fence-paint makers suggest roughly six panels per 5 litre tin for one coat on one side, so allow a full 5 litres for every five or six panels.
Do I need two coats of stain?
Usually. Two thin coats give more even colour and better protection than one thick coat, especially on new or weathered wood. Some one-coat fence treatments need only one coat when you are not changing colour. Over-applying penetrating stain leaves a sticky surface that peels, so follow the label.
Why does rough or old wood need more stain?
Rough-sawn, grooved and weathered wood has much more surface area and soaks up more product. Expect it to take around 1½ to 2 times as much as smooth planed boards. Brushing it in also uses more than you might expect from the label’s best-case figure.
Should I stain both sides of a fence?
Both sides last longer if they are treated, because bare wood on one side still takes in water. If the far side faces a neighbour’s garden, ask before treating or painting it. Choose “both sides” to double the area.
Can I use the paint calculator instead?
For painted wood siding or trim, yes. For stains, oils and fence treatments, use this calculator: they cover far less area per gallon or litre than wall paint, and the second coat behaves differently.