How to Stain a Deck or Fence

A good stain or fence treatment keeps water and sunlight out of the wood and can add years to a deck or fence. Most finishes that fail early do so because of the preparation or the weather, not the product. Here is how to choose the right finish, prepare the wood, and apply thin, even coats that last.

By Rohan Vijay · Checked by Shivam Sharma and Muskan Gupta · Updated

Choose the right product

ProductLookGood forRecoat roughly every
Clear sealer / water repellentNatural wood, no colourNew wood you want to weather naturally1 year
Semi-transparent (penetrating) stainColour with the grain showingMost decks and good-quality fences2–3 years
Solid colour (opaque) stainPaint-like, hides the grainOlder, patchy or mismatched wood3–5 years on fences, less on decks
Decking oilRich, natural finishHardwood and softwood decks1–2 years
Fence & shed paint / garden wood treatmentColoured, mattRough-sawn fence panels, sheds (common in the UK)Varies by product — often 2–5 years

The more pigment a finish has, the longer it protects against sunlight — but film-forming finishes on a deck are walked on and can wear or peel in traffic areas. Penetrating stains and oils soak in, so they wear away gradually instead of flaking, and are easy to recoat. Recoat times vary a lot with sun, rain and foot traffic.

To work out how much to buy, use the deck and fence stain calculator: rough-sawn and weathered wood soak up far more than the best-case figure on the tin.

Pick the right day

  • Mild and dry. Most products are applied between about 50 °F and 90 °F (10–32 °C). Check the tin.
  • No rain forecast for at least 24 hours, and none in the last day or two — the wood must be dry.
  • No direct midday sun or strong wind. Stain applied to hot boards dries too fast, leaving lap marks. Work on shaded sections, or in the morning and late afternoon.
  • Not too late in the year. Dew and cold nights slow drying; many products need several hours above their minimum temperature.

Is new wood ready?

Pressure-treated wood is often sold wet and may need weeks to dry before it will take stain. Sprinkle a little water on a board: if it beads on the surface, wait; if it soaks in within a few minutes, the wood is ready. Kiln-dried after treatment (KDAT) boards can usually be finished straight away. Some fence and shed treatments are designed to go on new treated timber — the tin will say.

What you will need

  • Your stain, oil or fence paint — the same batch for the whole job
  • Deck or fence cleaner, a stiff brush and a hose; a pressure washer is optional
  • Stripper and wood brightener if you are removing an old finish
  • Sandpaper (60–80 grit) or a sanding pole
  • A good synthetic brush for water-based products (natural bristle for oil-based), a deck pad or roller on a pole, and optionally a garden sprayer or paint sprayer
  • Plastic sheeting and masking tape to protect walls, plants and paving
  • Gloves and eye protection; a mask when sanding or spraying

1. Repair and clean

  1. Fix problems first. Replace split or rotten boards, punch down raised nails or swap them for screws, and tighten loose rails.
  2. Clean the wood. Scrub with a deck or fence cleaner to remove dirt, algae, mould and grey, weathered fibres, then rinse thoroughly.
  3. Strip any failing finish. New stain will not stick to old stain that is peeling or flaking. Use a stripper made for the old product, then a brightener to neutralise it and restore the wood’s colour.
  4. Go gently with a pressure washer. Use a wide fan tip, keep it moving and stay back from the surface. Too much pressure tears up the soft wood fibres and leaves a fuzzy surface that has to be sanded.

Let the wood dry for at least a day or two afterwards — longer in cool weather.

2. Sand if needed

Sand away any raised, furry fibres and smooth rough spots with 60–80 grit paper. Do not sand finer than about 80–100 grit for a penetrating stain: very smooth wood takes in less stain. Sweep or blow away all the dust.

3. Protect the surroundings

Cover plants, paving and the bottom of house walls with plastic sheeting, and mask off anything you do not want stained. Stain splashes on brick, render and concrete are hard to remove. If you are treating a fence, agree it with your neighbour first — especially if you plan to spray or to treat their side.

4. Test a patch

Try the stain on an offcut or a hidden board and let it dry. Colour depends on the wood species, its age and how much it soaks up, and the colour on the tin or chart is only a guide.

5. Apply thin, even coats

Decks

  1. Stir the stain well (do not shake it) and keep stirring now and then. Mix several tins together in a large bucket for a big deck.
  2. Do the railings, balusters and steps first, top down, so drips on the floor are covered later.
  3. Start at the side furthest from the steps or door, so you do not paint yourself in.
  4. Work along two or three boards at a time for their full length, keeping a wet edge, so you never stop in the middle of a board. Stopping halfway leaves a dark lap mark.
  5. If you use a roller, pad or sprayer, brush the stain into the boards and gaps afterwards (back-brushing). It pushes the stain into the grain and evens it out.
  6. For penetrating stains, wipe up any excess that has not soaked in after the time on the label. Puddles of stain stay sticky and peel.

Fences

  1. Work one panel or one bay at a time, from the top down, brushing along the grain.
  2. Get the finish into the overlaps of featheredge and lap boards, the edges of the boards and the tops of posts and rails, where water sits longest.
  3. A sprayer is much faster on rough-sawn panels; follow it with a brush to work the product in, and do not spray on windy days.

6. Second coats and drying

Follow the tin. Some penetrating stains are applied wet on wet — the second coat goes on before the first dries — while others, and most fence paints, need a few hours between coats. A second coat of penetrating stain uses much less than the first, because the wood is already partly sealed. As a guide, decks can usually take light foot traffic after about 24 hours and furniture after about 48 hours, but check the product.

Keep it looking good

  • Sweep the deck regularly and clear leaves and debris from between boards and from the bottom of fences.
  • Wash it once a year with a mild deck cleaner.
  • Splash a little water on the busiest area each spring: when it stops beading and soaks in quickly, it is time for a maintenance coat.
  • Recoat with the same type of product. Switching from a film-forming finish to a penetrating one means stripping it first.

Common problems

ProblemUsual cause
Peeling or flakingStain over a dirty or old, failing finish; too thick a coat; wood was damp
Sticky, tacky surfaceToo much penetrating stain left on the surface
Dark stripes and lap marksStopping mid-board, or staining in hot sun
Blotchy colourUneven cleaning or sanding; tins from different batches; no stirring
Fades or greys within a yearClear or very light finish in full sun — use a more pigmented product

Still planning the build? The deck calculator counts boards, joists and screws, and the fence calculator works out posts, rails and panels.

Calculators for this project