How to Lay a Paver Patio: Base, Sand and Laying Step by Step
A paver patio is one of the few hard-landscaping jobs where a careful beginner can match a professional finish — because almost all of the quality is in the base you cannot see. This guide covers the layers, the digging depth, the slope, laying and compacting, with a full materials list for a 12 × 10 ft (4 × 3 m) patio in US and UK units.
What goes under a paver patio
Pavers and block paving are a flexible surface: they sit on sand over compacted stone, held tight by an edge restraint. From the top down:
| Layer | What it does | US | UK |
|---|---|---|---|
| Pavers | The surface | 2⅜ in thick concrete pavers | 50–60 mm block paving |
| Jointing sand | Locks the pavers together | Polymeric or fine dry sand | Kiln-dried sand |
| Bedding sand | A thin, level bed | 1 in concrete sand | 30–40 mm sharp sand |
| Compacted base | Carries the load, drains water | 4–6 in crushed stone | 100–150 mm MOT Type 1 |
| Subgrade | Firm, compacted soil | — | — |
Large patio slabs and natural stone are different: they are usually laid on a full bed of mortar rather than sand. The base underneath is the same, and the paver calculator covers both.
1. Plan the size, pattern and slope
- Size it to the pavers. Lay out a row of pavers dry and adjust the patio’s length and width to whole pavers where you can. It saves hours of cutting.
- Choose the pattern. Running bond (stretcher bond) is quickest and wastes about 5%. Herringbone locks together best — it is the usual choice for driveways — but needs 10% extra for the cuts at the edges.
- Build in a slope. Water must run off, away from the house: about ¼ inch per foot in the US, or 1 in 60 to 1 in 80 in the UK (12–16 mm per metre). Set string lines to this fall before you dig.
- Check before digging. Find buried pipes and cables — in the US, call 811. Keep the finished surface at least 6 in (150 mm) below the damp-proof course or siding of the house.
2. Dig out
Dig to the depth of all the layers: base + bedding sand + paver thickness. For a typical patio that is about 7–8 in (180–200 mm) below the finished level. Dig 6–12 in (150–300 mm) wider than the patio on every side so the base supports the edge restraints. A 12 × 10 ft patio produces about 3½ cubic yards of soil; a 4 × 3 m patio, about 2.7 m³ — more than it looks, so plan where it will go.
Compact the exposed soil with a plate compactor. On soft or clay ground, lay a geotextile membrane before the base.
3. Build the base
Spread the crushed stone in layers of no more than 3–4 in (75–100 mm) and compact each one with several passes of the plate compactor, dampening it lightly if it is dusty. The finished base should follow the slope of the patio and be flat enough that a straightedge shows no gaps over about ⅜ in (10 mm). Compacted stone shrinks, so order about 15% more than the finished volume.
This is the step that decides whether the patio stays flat. If the base moves, the pavers will too.
4. Fix the edge restraints
Without a firm edge, pavers creep outwards and the joints open up. Use plastic or aluminium paver edging spiked into the base (common in the US), or kerbs and edging blocks bedded and haunched in concrete (common in the UK). Fit at least two sides before laying, using a builder’s square or the 3-4-5 rule to get corners true.
5. Screed the bedding sand
Lay two straight pipes or battens on the base as rails, spread the sand between them and pull a straight board along the rails to level it. Lift the rails out and fill the grooves. The bed should be an even 1 in (25 mm) in the US, or 30–40 mm before compaction in the UK. Do not walk on it or compact it — the pavers are bedded into it later — and only screed as much as you will cover that day.
6. Lay the pavers
- Start from a straight edge or a square corner — usually against the house — and work outwards, standing on the pavers you have laid.
- Place each paver straight down against its neighbours. Most have small spacer nibs that set the joint at about ⅛ in (2–5 mm).
- Mix pavers from several packs as you go to blend any colour variation.
- Check the lines with a string every few rows.
- Cut the edge pieces last, with a block splitter or a diamond blade. Wear eye, ear and dust protection — cutting concrete produces silica dust, so cut wet or use dust extraction.
7. Compact and fill the joints
Run the plate compactor over the whole patio to bed the pavers into the sand — with a rubber mat on the plate if the pavers have a delicate finish. Sweep dry jointing sand across the surface until the joints are full, compact again, and top up. If you use polymeric sand, sweep and blow every grain off the surface before misting it with water, following the instructions on the bag — any left on top will set as a haze.
Materials list: a worked example
From the paver calculator, with 5% extra pavers, a 4 in (100 mm) base, and a sand bed of 1 in (US) or 40 mm (UK):
| US: 12 × 10 ft (120 ft²) | UK: 4 × 3 m (12 m²) | |
|---|---|---|
| Pavers | 567 × 4 × 8 in pavers | 630 × 200 × 100 mm blocks |
| Base | About 3 tons (1.7 yd³) of crushed stone | About 2.9 tonnes of MOT Type 1 (4 bulk bags) |
| Bedding sand | 22 bags of 0.5 ft³, or 0.4 yd³ loose | About 0.85 tonnes of sharp sand (1 bulk bag) |
| Edge restraint | About 44 ft, less any side against the house | About 14 m, less any side against the house |
| Jointing sand | 1–2 bags — check the coverage on the bag | 1–2 bags of kiln-dried sand |
| Hire | Plate compactor, block splitter or saw | Plate compactor (wacker plate), block splitter |
For loose stone and sand by the ton, the gravel calculator gives weights for other materials and depths. For an awkward shape, work out the area first with the square footage calculator.
Common mistakes
- Too thin a base. Skimping here causes most sunken and uneven patios. Go deeper on clay, on made-up ground and anywhere a vehicle might drive.
- Using the sand to fix levels. The sand bed should be an even thickness. Correct dips and humps in the base, not with extra sand.
- No fall. A dead-level patio holds puddles and sends water towards the house.
- No edge restraint. Even a patio surrounded by lawn needs one.
A patio for foot traffic is a realistic DIY job. Driveways, retaining edges and anything beside a building’s foundations carry more load and may need a deeper base or professional advice. Prefer a poured slab? See how to plan a concrete patio.