How to use the rebar calculator
- Enter the length and width of the slab.
- Enter the bar spacing, measured centre to centre. The same spacing is used in both directions.
- Enter the edge cover — how far the ends of the bars stop short of the slab edge.
- Choose the bar size and the length your supplier stocks, usually 20 ft in the US or 6 m in the UK.
The rebar formula
Bars lengthwise = (slab width − 2 × cover) ÷ spacing, rounded down, + 1 Bars crosswise = (slab length − 2 × cover) ÷ spacing, rounded down, + 1 Bar length = slab dimension − 2 × cover (+ 40 bar diameters per splice) Total length = bars lengthwise × their length + bars crosswise × their length Weight = total length × weight per foot or metre
Where a bar has to be longer than a stock length, two bars are overlapped and tied together. The calculator adds a lap of 40 bar diameters for each splice — 20 in for #4 bar, or 400 mm for 10 mm bar.
Worked example (US)
A 20 × 10 ft slab with #4 bars at 12 in centres and 3 in of cover. Lengthwise: (120 − 6) ÷ 12 = 9, + 1 = 10 bars of 19 ft 6 in. Crosswise: (240 − 6) ÷ 12 = 19, + 1 = 20 bars of 9 ft 6 in. Total 385 ft, weighing 257 lb. With 10% extra, buy 22 bars of 20 ft.
Worked example (UK)
A 6 × 3 m slab with 10 mm bars at 200 mm centres and 50 mm of cover. Lengthwise: (3,000 − 100) ÷ 200 = 14, + 1 = 15 bars of 5.9 m. Crosswise: (6,000 − 100) ÷ 200 = 29, + 1 = 30 bars of 2.9 m. Total 175.5 m, weighing 108 kg. With 10% extra, buy 33 bars of 6 m — or use 2 sheets of mesh instead.
Rebar sizes and weights
| US bar | Diameter | lb per ft | UK bar | kg per m |
|---|---|---|---|---|
| #3 | ⅜ in (9.5 mm) | 0.376 | 8 mm (H8) | 0.395 |
| #4 | ½ in (12.7 mm) | 0.668 | 10 mm (H10) | 0.617 |
| #5 | ⅝ in (15.9 mm) | 1.043 | 12 mm (H12) | 0.888 |
| #6 | ¾ in (19.1 mm) | 1.502 | 16 mm (H16) | 1.579 |
The two columns are separate ranges, not exact equivalents: a #4 bar is slightly thicker than a 12 mm bar.
Rebar or mesh?
For a house slab, patio or shed base, welded steel mesh is often quicker than tying individual bars. In the UK, fabric mesh comes in 4.8 × 2.4 m sheets — A142 for light slabs, A193 or A252 for driveways and heavier loads — overlapped by at least 300 mm where sheets meet. In the US, welded wire reinforcement comes in rolls and flat sheets. Individual bars are used for footings, thickened edges, beams and anywhere an engineer specifies them.
Either way, the steel only works if it sits within the concrete: support it on chairs or spacers, tie the intersections with wire, and keep it clear of the edges. To work out the concrete itself, use the concrete calculator; for planning the whole job, see how to plan a concrete patio.
This calculator gives quantities for a simple single-layer grid. It does not design reinforcement: for foundations, suspended slabs, retaining walls and anything structural, follow an engineer’s drawings.
Frequently asked questions
How much rebar do I need for a concrete slab?
Lay bars in a grid both ways. Divide the slab’s width by the spacing and add one to get the number of bars running lengthwise, and do the same along the length for the bars running across. A 20 × 10 ft slab with bars at 12 in centres needs 10 bars one way and 20 the other: 385 ft of rebar, or 22 stock lengths of 20 ft with 10% extra.
What spacing should rebar be?
For patios, paths and shed bases, a grid at 18–24 in (450–600 mm) is common; driveways and garage floors more often use 12–18 in (300–450 mm). Structural slabs, footings and anything load-bearing must follow an engineer’s drawings or your local code — spacing and bar size are a structural decision.
What size rebar should I use?
In the US, #3 (⅜ in) is typical for patios and paths and #4 (½ in) for driveways, garage slabs and footings. In the UK, 10 mm or 12 mm bars are the usual equivalents — although domestic slabs there are more often reinforced with sheets of steel mesh such as A142 or A193.
How much does rebar weigh?
#3 bar weighs 0.376 lb per foot, #4 0.668 lb, #5 1.043 lb and #6 1.502 lb. Metric bar weighs its diameter squared × 0.00617 kg per metre: 10 mm is 0.617 kg/m, 12 mm 0.888 kg/m and 16 mm 1.58 kg/m. A 20 ft length of #4 weighs 13.4 lb; a 6 m length of 12 mm, 5.3 kg.
How far should rebar be from the edge of the concrete?
Steel needs concrete cover to protect it from rust: about 3 inches (75 mm) where concrete is cast against the ground, and 1½–2 inches (40–50 mm) from formed edges and the top surface. Support the grid on bar chairs or spacers so it sits in the slab rather than on the ground beneath it.