How to Lay a Gravel Driveway: Layers, Depths and Materials

A gravel driveway is cheaper than concrete or block paving, drains naturally and is well within reach of a determined DIYer. Most problems — ruts, weeds, gravel spreading onto the lawn — come from skipping the layers underneath. Here is how to build one properly, with tonnages for a typical driveway in US and UK units.

By Rohan Vijay · Checked by Shivam Sharma and Muskan Gupta · Updated

How a gravel driveway is built

A driveway that lasts has three layers below the gravel you see:

LayerWhat it doesUSUK
Firm subgradeThe dug-out, compacted soil——
Geotextile membraneStops stone sinking into soil; slows weedsWoven driveway fabricGeotextile membrane
Compacted sub-baseCarries the weight of vehicles4–6 in+ crusher run / road base150 mm+ MOT Type 1
Top gravelThe surface you drive on2–3 in40–50 mm

Soft or clay ground needs a deeper sub-base — 8 in (200 mm) or more — and heavy vehicles more again. If you are unsure, dig a test hole after rain and see how the ground behaves.

1. Check the rules and plan drainage

  • Permission: in the US, check local rules for driveway permits, especially where a new driveway meets the road. In England, front gardens surfaced with permeable materials such as gravel do not normally need planning permission, but a new dropped kerb onto the road needs council approval.
  • Drainage: gravel drains through, but the ground underneath still needs somewhere for water to go. Give the driveway a slight fall away from the house, and avoid sending water onto a neighbour’s property or the road.
  • Utilities: find out where buried pipes and cables run before digging. In the US, call 811.

2. Dig out and compact

Remove turf, topsoil and roots down to firm ground — the depth of the sub-base plus the gravel, typically 8 in (200 mm) below the finished level. Compact the exposed soil with a plate compactor, filling any soft spots. For a 40 × 12 ft driveway that is about 12 cubic yards of soil to remove; for a 10 × 3 m driveway, about 6 m³ — plan for a skip, dumpster or a grab lorry.

3. Lay the membrane

Roll out the geotextile over the whole area, overlapping joints by at least 12 in (300 mm). It keeps the expensive sub-base from mixing into the soil — the main reason gravel driveways develop ruts. Allow 10–20% extra for overlaps and edges.

4. Fit edging

Without edges, gravel migrates onto lawns and paths. Use timber boards, steel edging, bricks or concrete kerbs set slightly higher than the finished gravel. Concrete haunching (a wedge of concrete behind the kerb) holds kerbs in place — the concrete calculator works out how much.

5. Build up and compact the sub-base

Spread the sub-base in layers no thicker than about 3–4 in (75–100 mm) and compact each layer with several passes of the plate compactor. Compacted stone shrinks noticeably, so order about 15% more than the flat volume.

6. Spread the top gravel

Spread the gravel evenly to 2–3 in (40–50 mm) and rake it level. Deeper is not better: thick loose gravel is hard to walk and drive on and shifts more. Roll or lightly compact it to settle it in.

Which gravel? Angular crushed stone, about ⅜–¾ in (10–20 mm), locks together and stays put. Smooth, rounded pea gravel looks good but rolls underfoot and under tyres, so it is better for paths than for driveways. For very steep slopes or heavy use, plastic gravel stabiliser grids under the top layer stop it moving.

How much to order: a worked example

Using the gravel calculator with typical densities:

US: 40 × 12 ft (480 ft²)UK: 10 × 3 m (30 m²)
Sub-base6 in crusher run + 15% → about 18 tons (10.2 yd³)150 mm MOT Type 1 + 15% → about 10.9 tonnes
Top gravel2 in crushed stone + 10% → about 4.4 tons (3.3 yd³)50 mm 20 mm gravel + 10% → about 2.6 tonnes (4 bulk bags)
MembraneAbout 550 ft²About 35 m²

At these quantities, buy loose by the ton or tonne from a quarry or builders’ merchant rather than in bags — the sub-base alone would be 13 bulk bags in the UK, and a tipper lorry is usually far cheaper. Check access: a loaded truck is heavy and needs room to tip.

Looking after a gravel driveway

  • Rake it level a few times a year, especially where tyres turn.
  • Top up with a little fresh gravel every year or two as it thins.
  • Pull weeds while they are small, and keep leaves off so they do not rot into soil in the gravel.
  • In winter, use grit or a little rock salt on icy patches — see the ice melt calculator.

The same compacted sub-base is the foundation for a tarmac or asphalt driveway, if you later decide to surface it. The asphalt calculator works out the tonnage for the binder and surface courses.

Calculators for this project