Roof Pitch Calculator

Find a roof’s pitch from its rise and run, from the span of the house and the height of the ridge, or from an angle — and convert between x/12 pitch, degrees and percent slope, with the rafter length and slope factor.

Find your roof pitch

What do you know?
in cm
Vertical height gained
in cm
Horizontal distance

Results

How to use the roof pitch calculator

  1. Choose what you can measure. Rise and run suits a measurement taken against a rafter with a level. Span and height suits plans, or a measurement of the house width and the ridge height. Angle converts a pitch in degrees — common on UK drawings — to other forms.
  2. Enter the measurements. For a symmetrical gable roof, the run of each side is half the span.
  3. Read off the pitch in x/12, degrees and percent, the slope factor and — for span and height — the rafter length.

Roof pitch formulas

Pitch (x/12) = rise ÷ run × 12 Angle (°) = arctan(rise ÷ run) Slope (%) = rise ÷ run × 100 Slope factor = 1 ÷ cos(angle) Rafter length = (run + overhang) × slope factor

For a gable roof, run = span ÷ 2 and rise = the ridge height above the top of the walls. The rafter length here is measured along the slope from the ridge line to the end of the eaves; the actual cut rafter is a little shorter at the ridge to allow for the ridge board.

Worked example (US)

A roof rises 6 inches for every 12 inches of run: 6 ÷ 12 × 12 = 6/12 pitch, arctan(0.5) = 26.6°, a 50% slope and a slope factor of 1.118. On a 24 ft span with a 6 ft ridge height, each side runs 12 ft; with a 1 ft overhang the rafter is 13 × 1.118 = 14.53 ft.

Worked example (UK)

A rise of 70 cm over a run of 100 cm is arctan(0.7) = 35.0°, or about 8.4/12. On a 7.2 m span with the ridge 2.5 m above the wall plate, each side runs 3.6 m and the pitch is 34.8°; with a 300 mm overhang the rafter is 3.9 × 1.217 = 4.75 m.

Roof pitch chart

PitchDegreesSlopeSlope factor
1/124.8°8.3%1.003
2/129.5°16.7%1.014
3/1214.0°25%1.031
4/1218.4°33.3%1.054
5/1222.6°41.7%1.083
6/1226.6°50%1.118
7/1230.3°58.3%1.158
8/1233.7°66.7%1.202
9/1236.9°75%1.250
10/1239.8°83.3%1.302
11/1242.5°91.7%1.357
12/1245.0°100%1.414
14/1249.4°116.7%1.537
16/1253.1°133.3%1.667
18/1256.3°150%1.803

What your pitch means

  • Under 2/12 (about 9.5°): a low-slope or flat roof. Shingles and tiles will leak; it needs a continuous membrane. In the UK, roofs under 10° are classed as flat.
  • 2/12 to 4/12 (9.5–18.4°): low slope. Asphalt shingles are allowed from 2/12 in US codes, with a double layer of underlayment below 4/12. Many tiles need a steeper roof.
  • 4/12 to 9/12 (18.4–36.9°): conventional pitched roofs. Suitable for most shingles, tiles and slates, and the easiest to work on.
  • Over 9/12 (36.9°): steep. Roofers need harnesses and roof jacks or scaffolding, which raises labour costs.

Minimum pitches vary by product, so always check the manufacturer’s figures for your shingle, tile or slate, and your local code.

Frequently asked questions

What is a 6/12 roof pitch in degrees?

A 6/12 pitch — 6 inches of rise for every 12 inches of horizontal run — is 26.6°, a 50% slope. Other common pitches: 4/12 is 18.4°, 8/12 is 33.7° and 12/12 is 45°.

How do I measure my roof pitch?

From the loft or attic, hold a level horizontally against the underside of a rafter, mark 12 inches (or 300 mm) along the level, and measure straight up from that mark to the rafter. That height is the rise for that run. You can also measure the span of the house and the height of the ridge above the wall plate, and use the “span and height” option.

What is the minimum pitch for shingles?

US building codes allow asphalt shingles on roofs of 2/12 or steeper, with a double layer of underlayment between 2/12 and 4/12. Below 2/12, a roof is treated as low-slope or flat and needs a membrane such as EPDM, TPO or modified bitumen.

What is the minimum pitch for roof tiles and slates in the UK?

It depends on the product, so check the manufacturer’s data. As a rough guide, interlocking concrete tiles are rated down to somewhere between about 15° and 30° depending on the tile, large natural slates to about 20° (smaller slates need a steeper roof), and traditional plain tiles need about 35°. Roofs under 10° are classed as flat roofs.

What is the slope factor?

The slope factor (or pitch multiplier) is how much longer a rafter is than its horizontal run — and how much bigger the roof surface is than the area it covers. For a 6/12 pitch it is 1.118, so a 1,000 ft² footprint has about 1,118 ft² of roof. The roofing calculator uses it to estimate shingles and tiles.

What is the difference between pitch and slope?

In everyday use they mean the same thing. Strictly, US roofers express slope as rise per 12 inches of run (6/12) and sometimes use “pitch” for rise divided by the full span, so a 6/12 slope is a 1/4 pitch. In the UK, roof pitch is normally given in degrees.

Built by Paras Garg and checked by Shivam Sharma and Muskan Gupta. Formulas and figures last reviewed on . Results are estimates: product yields vary, so check manufacturer labels and local building rules before you buy or build. Spotted an error? Tell us.