Concrete Block Calculator

Find how many concrete blocks, cinder blocks or breeze blocks you need for a wall, and how much mortar — in bags of mortar mix, or cement and sand — using US or UK block sizes.

Calculate blocks for a wall

ft m
ft m
ft² m²
Doors, windows, gates
%
in mm
in mm
in mm
The thickness of the wall
in mm
$ £

Results

How to use the concrete block calculator

  1. Enter the length and height of the wall, and subtract any doors, windows or gates.
  2. Check the block size. The defaults are the standard US 8 × 8 × 16 in block (actual size 7⅝ × 7⅝ × 15⅝ in) and the standard UK 440 × 215 × 100 mm block.
  3. Change the thickness if you are using 4, 6, 10 or 12-inch blocks, or 140 mm or 215 mm blocks. It does not change the number of blocks, but it does change the mortar.
  4. Keep 5% extra for cuts and breakages — 10% if the wall has many corners, piers or openings.

The block formula

Blocks = wall area ÷ ((length + joint) × (height + joint)) × (1 + waste) Mortar = blocks × joint volume per block × 1.3

The joint volume is the mortar bed and one end joint for each block, across the full thickness of the wall. The 1.3 factor allows for mortar that is dropped or squeezed out, and matches the usual rating of about 12 standard blocks per 80 lb bag of mortar mix.

Worked example (US)

A 20 × 4 ft garden wall is 80 ft². At 1.125 blocks per ft², that is 90 blocks — 95 with 5% extra. The mortar comes to about 4.6 ft³, or 8 bags of 80 lb mortar mix.

Worked example (UK)

A 5 × 1.8 m wall is 9 m². At 9.88 blocks per m², that is 89 blocks — 94 with 5% extra. The mortar is about 0.08 m³: 2 bags of cement (25 kg) and about 125 kg of building sand at 1:4.

Standard block sizes

BlockActual sizeBlocks needed
US 4 × 8 × 16 in3⅝ × 7⅝ × 15⅝ in1.125 per ft²
US 6 × 8 × 16 in5⅝ × 7⅝ × 15⅝ in1.125 per ft²
US 8 × 8 × 16 in (standard)7⅝ × 7⅝ × 15⅝ in1.125 per ft²
US 12 × 8 × 16 in11⅝ × 7⅝ × 15⅝ in1.125 per ft²
UK 100 mm block440 × 215 × 100 mm10 per m²
UK 140 mm block440 × 215 × 140 mm10 per m²
UK 215 mm (block laid flat)440 × 100 × 215 mm20 per m²

US block sizes are named by their nominal size, which includes a ⅜-inch mortar joint. The thickness is listed first.

What else you will need

  • A footing. Block walls sit on a concrete strip footing, typically twice the wall’s width and below the frost line in cold climates — work it out with the concrete calculator.
  • Half blocks and corner blocks for the ends of alternate courses in stretcher bond, or allow extra full blocks to cut.
  • Reinforcement and core fill for retaining and structural walls, as specified by the engineer or your local code.
  • Coping or cap blocks to keep water out of the top of the wall: one per 16 in (or 440 mm) of wall length.

Building in brick instead? Use the brick calculator.

Frequently asked questions

How many concrete blocks do I need per square foot or square metre?

A standard US block is 16 × 8 inches on its face including the mortar joint, which is 0.89 ft² — so you need 1.125 blocks per square foot, or 112.5 per 100 ft². A standard UK block is 440 × 215 mm, which with 10 mm joints works out at 10 blocks per square metre.

How much mortar do I need for 100 blocks?

About 8½ bags of 80 lb mortar mix for 100 standard 8-inch US blocks — roughly 12 blocks per bag. For 100 UK blocks at 100 mm thick, allow about 0.09 m³ of mortar: roughly 32 kg of cement (just over one 25 kg bag) and 140 kg of building sand at a 1:4 mix. Thicker blocks need proportionally more.

What is the difference between a cinder block, a concrete block and a breeze block?

They are all concrete masonry units (CMUs). “Cinder block” and “breeze block” are older names from when coal cinders or ash (“breeze”) were used as lightweight aggregate. Today the blocks are made with sand, gravel or lightweight aggregates, and in the UK also as aerated (aircrete) blocks, but the old names are still used for all of them.

Do hollow blocks need to be filled with concrete?

Not for a low garden wall. Retaining walls and structural walls usually have steel bars in some or all of the cores, which are then filled with grout or concrete. As a rough guide, filling every core of standard 8-inch blocks takes about a quarter to a third of a cubic foot per block — around 1 cubic yard for every 100 blocks.

How high can I build a block wall?

That depends on its thickness, piers, footing and what it holds back. As a rule, retaining walls over about 4 ft (1.2 m) need to be designed by an engineer and often need a permit in the US. In England, a garden wall over 1 m next to a road, or 2 m elsewhere, needs planning permission. For anything tall, load-bearing or retaining soil, follow your local code or building regulations.

Built by Paras Garg and checked by Shivam Sharma and Muskan Gupta. Formulas and figures last reviewed on . Results are estimates: product yields vary, so check manufacturer labels and local building rules before you buy or build. Spotted an error? Tell us.