How to Grout Tile: Mixing, Applying and Cleaning Up
Grouting is the last step of a tiling job and the one that decides how it looks. It is not difficult, but it is unforgiving of rushing: mix too wet, work too large an area or clean up too late, and you will be scrubbing haze for days. Here is how to choose the right grout, work out how much to buy, and apply it cleanly on walls and floors.
Choose the right grout
| Grout | Use it for | Notes |
|---|---|---|
| Unsanded (US) / fine wall grout (UK) | Joints under ⅛ in (3 mm); polished stone, glass | Smooth; will shrink and crack in wide joints |
| Sanded (US) / wide-joint floor grout (UK) | Joints of ⅛ in (3 mm) and over; most floors | Sand resists shrinkage; can scratch soft or polished tile |
| Polymer-modified / flexible | Floors, underfloor heating, timber subfloors, showers | Most modern bagged grouts; better water and movement resistance |
| Epoxy | Wet rooms, kitchens, commercial floors | Waterproof and stain-proof; harder to work, short working time |
| Ready-mixed | Small wall areas, repairs | Convenient; slower to cure and not for every tile |
Match the grout to your joint width first, then to the room. Where the tiles will get wet or the floor may flex, choose a flexible, water-resistant grout. Pick the colour with a tile and a sample card in the room’s own light: a contrasting colour shows every uneven joint, while one close to the tile hides them.
Work out how much you need
The amount depends on the tile size, the joint width and the tile’s thickness — small tiles and wide joints use far more. The grout calculator does the sum for any combination. As a guide:
| Tile and joint | US | UK |
|---|---|---|
| 12 × 12 in (300 mm) tile, ⅛ in (3 mm) joint | A 10 lb bag covers about 150 ft² | A 5 kg bag covers about 17 m² |
| 12 × 24 in (300 × 600 mm) tile, ⅛ in (3 mm) joint | A 10 lb bag covers about 205 ft² | A 5 kg bag covers about 23 m² |
| 2 × 2 in (50 mm) mosaic, ⅛ in (3 mm) joint | A 10 lb bag covers about 40 ft² | A 5 kg bag covers about 4 m² |
Buy about 10% more than the estimate, all from the same batch, and keep the leftover powder sealed and dry for repairs.
What you will need
- Grout, and a clean bucket for mixing
- A rubber grout float
- A margin trowel or a paddle mixer on a slow drill
- Two buckets of clean water and a large grout sponge with rounded edges
- Microfibre cloths for the final polish
- Silicone sealant or caulk in a matching colour for corners and edges
- Gloves and eye protection — cement grout is alkaline and irritates skin
1. Prepare the joints
- Wait for the adhesive to set — usually 24 hours for standard adhesive or thinset, or as the bag says.
- Remove the spacers and rake out any adhesive that has squeezed up into the joints. Grout needs at least two-thirds of the tile’s depth to bond.
- Vacuum and wipe the tiles so no dust or grit ends up in the grout.
- Seal porous tiles first. Natural stone, unglazed and textured tiles can be stained by grout pigment; a coat of sealer or grout release beforehand makes cleaning far easier.
2. Mix it properly
Add the powder to the measured water, not the other way round, and mix to a smooth paste about as thick as peanut butter — it should hold its shape on the trowel. Let it stand for 5–10 minutes (this is called slaking), then stir again without adding water. Too much water is the commonest cause of weak, patchy, cracked grout.
Mix only as much as you can use in 20–30 minutes. Once it starts to stiffen, throw it away rather than re-wetting it.
3. Fill the joints
- Scoop grout onto the tiles and spread it with the float held at about 45°, working diagonally across the joints so the float presses grout in rather than dragging it out.
- Go over each area two or three times from different directions until every joint is packed full, with no holes.
- Scrape off the excess with the float held almost upright, again moving diagonally.
- Work in sections of about 10–15 ft² (1–1.5 m²) — smaller in a warm room.
Do not grout the joints where tiles meet a bath, shower tray, worktop, or another wall or floor. Those are movement joints: leave them empty for sealant.
4. Clean off at the right moment
Wait until the grout has firmed up — usually 10–20 minutes, when a fingertip pressed on a joint leaves a mark but picks up no grout. Then:
- Wring the sponge out until it is only damp. A wet sponge washes cement out of the joints and leaves them weak and pale.
- Wipe lightly across the tiles in a circular motion to loosen the surface grout, then make single diagonal passes, turning to a clean face of the sponge each time.
- Rinse the sponge often and change the water as soon as it turns cloudy.
- Shape the joints with the sponge or a rounded tool so they are even and very slightly below the tile surface.
After another hour or so a dry haze appears. Buff it off with a dry microfibre cloth. Haze left for days sets hard and needs a grout haze remover.
5. Seal the edges and let it cure
- Sealant. After 24 hours, run silicone or matching caulk along the movement joints you left empty.
- Keep it dry. Most grouts can be walked on after 24 hours, but keep showers dry for 2–3 days, or as the product directs, and avoid heavy cleaning for a week.
- Seal the grout if it is a standard cement-based product in a shower, kitchen or on a floor — typically after 2–3 days’ curing. Stain-resistant and epoxy grouts do not need sealing.
Common problems
| Problem | Usual cause |
|---|---|
| Patchy or pale colour | Too much water in the mix or on the sponge; different batches |
| Cracks or pinholes | Mix too wet; joints not packed full; unsanded grout in wide joints |
| Grout sits low in the joints | Sponging too soon or too hard |
| Stubborn haze | Cleaning too late, or dirty rinse water |
| Cracks along corners and edges | Grout used where flexible sealant was needed |
Still planning the tiling itself? The tile calculator works out how many tiles to buy, and how much extra material to buy explains waste allowances for different layouts.