How to Build a Retaining Wall with Blocks
A low retaining wall turns a slope into usable, level ground — and dry-stacked concrete blocks make it a realistic weekend project. What keeps the wall standing is not the blocks you see but the three things you do not: a level compacted base, a buried first course and drainage behind. This guide covers a garden wall up to about 3–4 ft (1.2 m), with a materials list in US and UK units.
First: is this a wall you should build yourself?
Soil is heavy, and wet soil far heavier. The force on a retaining wall rises steeply with height, so a wall twice as tall has to resist roughly four times the push. A low gravity wall relies on its own weight and a slight backward lean. Beyond that, walls need reinforcement and an engineered design.
| Situation | What to do |
|---|---|
| Up to about 3–4 ft (0.9–1.2 m), level ground above and below | Suitable for a careful DIY build, following the block maker’s instructions |
| Taller than that | Needs an engineer’s design, usually geogrid reinforcement, and often a permit |
| A slope, driveway, parking or building above the wall | Extra load — get professional advice at any height |
| Next to a boundary, road or public path | Check local rules; in England, walls over 1 m beside a highway or 2 m elsewhere need planning permission |
In many US jurisdictions a permit is required for walls over 4 ft measured from the bottom of the footing — which includes the buried part. Rules vary, so check before you dig, and locate buried utilities first (call 811 in the US).
How a block retaining wall works
- Base: about 6 in (150 mm) of compacted crushed stone, in a trench wider than the block.
- Buried course: the first row sits below ground level, so the bottom of the wall cannot slide forward.
- Setback: each course steps back slightly, leaning the wall into the slope. Most retaining wall blocks have a lip or pins that set this automatically.
- Drainage: clean stone and a perforated pipe behind the wall let water escape instead of building up pressure.
- Caps: a top row fixed with construction adhesive, which finishes the wall and ties the top course together.
1. Plan and mark out
Mark the front line of the wall with string and stakes, or a garden hose for curves. Decide the finished height, then add the buried depth — about one-tenth of the wall’s height, and at least 6 in (150 mm) — to get the total height of blockwork. Use the retaining wall calculator to turn that into courses, blocks and stone.
2. Dig the trench
Dig a trench along the line, wide enough for the block plus about 6 in (150 mm) in front and behind — roughly 24 in (600 mm) for a 12 in (300 mm) block — and deep enough for the base plus the buried course: about 12 in (300 mm). Cut back into the slope behind to make room for at least 12 in (300 mm) of drainage stone.
If the ground slopes along the length of the wall, step the trench down in whole-block heights, keeping each section level. Compact the bottom of the trench with a hand tamper or plate compactor.
3. Lay and level the base
Fill the trench with about 6 in (150 mm) of crushed stone — crusher run or ¾-inch minus in the US, MOT Type 1 in the UK — in two layers, compacting each one. Check it with a long level in both directions. Time spent here is never wasted: every course above copies the base, and a small error at the bottom becomes a visible lean at the top.
4. Set the first course
- Start at the lowest point of the wall.
- If the blocks have a rear lip, knock it off the first course (or lay them as the maker directs) so they sit flat on the base.
- Set each block, check it level front to back and side to side, and tap it down with a rubber mallet. Adjust the stone underneath rather than leaving a block rocking.
- Run a string line along the back of the blocks to keep the row straight.
This course takes longer than all the others put together. That is normal.
5. Add drainage
Lay a 4 in (100 mm) perforated drain pipe behind the first course, on the base, with a slight fall towards an outlet at the end of the wall or through its face. Line the cut slope with landscape fabric (geotextile), leaving enough spare at the top to fold over later. The fabric keeps soil from washing into the stone and clogging it.
6. Build up, backfilling as you go
- Sweep the top of each course clean before laying the next — a single stone chip will throw a block off level.
- Stagger the joints like brickwork, starting alternate courses with a half block. Cut blocks with a masonry blade or a block splitter, wearing eye, ear and dust protection.
- Pull each block forward against the lip or pins of the course below, so the setback is consistent.
- After every course, fill behind the wall with clean ¾ in (20 mm) stone, at least 12 in (300 mm) wide, and fill any hollow cores too. Place soil behind the stone and compact it in thin layers.
Do not build the whole wall and backfill afterwards: the backfill cannot then be compacted, and it will settle for years.
7. Cap and finish
Fold the fabric over the top of the drainage stone, then cover it with 4–6 in (100–150 mm) of topsoil so the area can be planted. Glue the cap blocks down with exterior masonry or landscape block adhesive, overhanging the face by about 1 in (25 mm). Grade the ground at the top so surface water runs away from the wall, not towards it.
Materials list: a worked example
From the retaining wall calculator, for a straight wall with 6 in (150 mm) buried and 5% extra blocks:
| US: 20 ft long, 3 ft high | UK: 6 m long, 0.9 m high | |
|---|---|---|
| Blocks | 111 × 16 × 6 × 12 in (7 courses of 15) | 111 × 400 × 150 × 300 mm (7 courses of 15) |
| Caps | 15 | 15 |
| Base stone | About 1.5 tons (0.85 yd³) | About 1.3 tonnes of MOT Type 1 (2 bulk bags) |
| Drainage stone | About 3.5 tons (2.6 yd³) of clean ¾ in stone | About 3 tonnes of clean 20 mm stone (4 bulk bags) |
| Drain pipe | 20 ft of 4 in perforated pipe, plus an outlet | 6 m of 100 mm perforated pipe, plus an outlet |
| Fabric | About 100 ft² of landscape fabric | About 10 m² of geotextile |
| Adhesive | 2–3 tubes of landscape block adhesive | 2–3 tubes of exterior masonry adhesive |
A standard retaining wall block of this size weighs 60–80 lb (27–36 kg), so 111 blocks is around 4 tons to move. Have the pallets dropped as close to the wall as possible, and lift with help. For other depths of stone, use the gravel calculator.
Common mistakes
- No drainage. The most frequent cause of bulging and collapse. Stone, pipe and an outlet are not optional, even on a low wall.
- A base that is not level or not compacted. It cannot be corrected higher up.
- Not burying the first course. A wall sitting on top of the ground can slide out at the bottom.
- Backfilling with clay or topsoil directly against the blocks. It holds water and pushes on the wall when it freezes.
- Building taller than the blocks are rated for. Every system publishes a maximum unreinforced height — stay under it.
Building a mortared wall of standard concrete blocks instead? That needs a concrete footing and, for retaining soil, steel reinforcement — see the concrete block calculator for quantities, and take professional advice on the design.