How to use the stair calculator
- Measure the total rise from the finished floor at the bottom to the finished floor at the top. Include flooring that is still to be laid.
- Enter the tallest riser you are happy with. Lower risers give a gentler stair but need more room.
- Enter the tread depth (in the UK, the “going”) — measured from the face of one riser to the next, not including the nosing overhang.
- Check the results against the rules shown, and confirm the stair fits the space you have.
The stair formulas
Risers = total rise ÷ maximum riser (rounded up) Riser height = total rise ÷ risers Treads = risers − 1 Total run = treads × tread depth Angle = arctan(riser height ÷ tread depth) Stringer = √(total rise² + total run²)
Worked example (US)
A 108-inch (9 ft) rise with risers of no more than 7½ inches: 108 ÷ 7.5 = 14.4, so 15 risers of 7.2 inches. With 10-inch treads there are 14 treads and a total run of 140 inches (11 ft 8 in). The stair rises at 35.8°, and the stringer is about 14.7 ft along the pitch line.
Worked example (UK)
A 2,600 mm rise with risers of no more than 200 mm needs 13 risers of exactly 200 mm. With a 240 mm going there are 12 treads and a total going of 2,880 mm. The pitch is 39.8° and 2R + G = 640 mm — within all the Approved Document K limits.
Stairs with a landing
Tick include a landing to split the staircase into two flights — for a straight stair that is too long for one flight, or for an L- or U-shaped stair that turns at a landing. The riser height stays the same all the way up; the landing replaces one tread, so each flight has one tread fewer than it has risers.
Lower flight run = (risers below the landing − 1) × tread depth Upper flight run = (risers above the landing − 1) × tread depth Straight footprint = lower run + landing depth + upper run
US example: the 108-inch stair above with a 36-inch landing halfway (after 8 risers) has a lower flight of 8 risers and 7 treads (70 in of run) and an upper flight of 7 risers and 6 treads (60 in). In a straight line it needs 166 in (13 ft 10 in) of floor.
UK example: the 2,600 mm stair with a 900 mm landing after 7 risers has a lower flight of 1,440 mm going and an upper flight of 1,200 mm — 3,540 mm in a straight line. For a quarter-turn (L-shaped) stair, each flight runs along its own wall instead.
Stair rules at a glance
| Rule | US (IRC, residential) | UK (Part K, private stair) |
|---|---|---|
| Riser height | Up to 7¾ in | 150–220 mm |
| Tread depth / going | At least 10 in | 220–300 mm |
| Steepest pitch | Set by riser and tread limits | 42° |
| Comfort rule | 2R + T ≈ 24–25 in (guide) | 2R + G = 550–700 mm |
| Headroom | 6 ft 8 in | 2.0 m |
| Landings | At least 36 in deep; one flight rises no more than 151 in | Top and bottom of every flight, at least as deep as the stair is wide |
Codes also cover handrails, guards, nosings, width and landings. Risers within one flight should all be the same height — the calculator divides the total rise evenly for that reason.
Tips
- Check the space. Make sure the total run plus a landing at the bottom fits the room, and that there is enough headroom along the whole flight.
- Account for flooring. If the bottom or top floor will get thicker flooring later, the first or last riser will end up a different height.
- Buying timber? The board foot calculator works out the volume and cost of stringers and treads.
- Building outdoor steps in concrete? Once you know the risers, the concrete steps calculator works out the concrete and bags of mix.
Frequently asked questions
How many steps do I need for a 9 ft (108 in) rise?
With risers no taller than 7½ inches, a 108-inch rise needs 15 risers of 7.2 inches and 14 treads. With the IRC maximum of 7¾ inches you could use 14 risers of about 7.7 inches, but the stair will be steeper.
What is the maximum riser height and minimum tread depth?
Under the US International Residential Code, risers can be up to 7¾ in and treads must be at least 10 in deep. For a private stair in England and Wales, Approved Document K allows a rise of 150–220 mm, a going of 220–300 mm and a pitch of no more than 42°. Local codes can differ, so always check with your building department or building control.
Why is there one less tread than risers?
The upper floor acts as the final step, so a staircase with 15 risers has 14 treads. The total run of the stair is therefore the number of treads × the tread depth.
What is the 2R + T (2R + G) rule?
It is a comfort rule: twice the riser height plus the tread depth should equal roughly one walking stride. In the US that is about 24–25 inches; UK regulations require 550–700 mm. Stairs outside that range feel awkward to climb.
When does a staircase need a landing?
In the US, the IRC limits one flight to a vertical rise of 151 inches (12 ft 7 in); taller stairs need an intermediate landing at least 36 inches deep. In England and Wales, Approved Document K requires a landing at the top and bottom of every flight, at least as deep as the stair is wide. Landings are also how a stair turns a corner in an L- or U-shaped layout.
How long should my stringers be?
The calculator gives the length along the pitch line from the bottom to the top of the stair. Buy boards at least a foot (300 mm) longer to allow for cutting the top and bottom joints.