US vs UK Building Material Sizes: A Side-by-Side Guide

A concrete bag, a paint tin and a sheet of drywall look the same on both sides of the Atlantic — but the sizes are not. Here is how US and UK building materials compare, with exact conversions and the numbers that matter when you are working out how much to buy.

By Rohan Vijay · Checked by Shivam Sharma and Muskan Gupta · Updated

The golden rule: convert the job, not the product

The most common mistake when following an American video in the UK (or a British guide in the US) is converting a product count: “the video says 56 bags, so I need 56 bags.” US and UK bags, tins and boards are different sizes, so the count is wrong. Instead, convert the area or volume of the job, then divide by the size of the product you can actually buy. Every CalcBrook calculator does this for you when you switch between US and UK units.

Quick conversion table

US unitMetric equivalentExact?
1 inch25.4 mmExact
1 foot0.3048 m (304.8 mm)Exact
1 square foot0.0929 m²Exact: 0.09290304
1 cubic yard0.7646 m³Exact: 0.764554857984
1 US gallon3.785 litresExact: 3.785411784
1 pound (lb)0.4536 kgExact: 0.45359237
1 US (short) ton907.2 kg2,000 lb

Two traps: a US gallon (3.785 L) is smaller than the old imperial gallon (4.546 L) still seen in some British contexts, and a US ton (907 kg) is lighter than the metric tonne (1,000 kg) used by UK merchants.

Concrete and mortar

USUK
Bag sizes40, 60, 80 lb (18, 27, 36 kg)20 and 25 kg
Yield0.30, 0.45, 0.60 ft³ per bag≈ 0.0094 m³ (20 kg), 0.0117 m³ (25 kg)
Bags per unit of concrete45 × 80 lb per cubic yard≈ 107 × 20 kg or 86 × 25 kg per m³
Ready-mix sold byCubic yardCubic metre (1 m³ = 1.31 yd³)

The underlying material is the same: about 2,136 kg of dry mix makes a cubic metre of concrete in both countries. Only the packaging differs. Mortar works the same way — an 80 lb bag of US mortar mix lays roughly 37 modular bricks. See the concrete calculator for bag counts in either system.

Paint

USUK
Container sizesQuart (0.95 L), gallon (3.79 L), 5-gallon pail (18.9 L)1 L, 2.5 L, 5 L, 10 L tins
Coverage on the labelft² per gallon (often 350–400)m² per litre (often 10–13)

350 ft² per gallon is about 8.6 m² per litre — a little lower than many UK tins claim, so do not assume a UK tin covers less just because the number looks different. A US gallon is only about three quarters of a 5 L tin. The paint calculator rounds to quarts and gallons, or to the least-waste mix of 5 L, 2.5 L and 1 L tins.

Drywall vs plasterboard

US drywallUK plasterboard
Standard sheet4 × 8 ft (1,219 × 2,438 mm)1,200 × 2,400 mm
Other common sizes4 × 10, 4 × 12 ft900 × 1,800, 900 × 2,400 mm
Standard thickness½ in (12.7 mm)12.5 mm
Thicker / fire-rated⅝ in (15.9 mm), Type X15 mm

The standard sheets are close but not identical: a US 4 × 8 sheet is 19 mm wider and 38 mm longer than a UK 2400 × 1200 board. Stud spacing follows the same pattern — 16 in (406 mm) centres in the US, 400 or 600 mm in the UK — so boards are designed to land on studs in each system. Count sheets with the drywall & plasterboard calculator.

Lumber vs timber

US softwood lumber is named by nominal size, but the actual planed size is smaller: a “2 × 4” is 1½ × 3½ in. UK timber is named by its actual metric size. Interestingly, UK CLS studwork at 38 × 89 mm is the same section as a US 2 × 4 — CLS stands for Canadian Lumber Standard.

US nominalUS actualClosest UK section
2 × 41½ × 3½ in (38 × 89 mm)38 × 89 mm CLS, or 47 × 100 mm sawn (“4 × 2”)
2 × 61½ × 5½ in (38 × 140 mm)47 × 150 mm sawn
2 × 81½ × 7¼ in (38 × 184 mm)47 × 200 mm sawn
4 × 43½ × 3½ in (89 × 89 mm)100 × 100 mm post

Lengths differ too: US lumber comes in 8, 10, 12 and 16 ft lengths; UK timber in 2.4, 3.0, 3.6 and 4.8 m — so a UK 2.4 m length is about 7 ft 10½ in, just short of an 8 ft board. US hardwood is sold by the board foot; UK hardwood by the cubic metre or cubic foot.

Bricks

US modular brickUK standard brick
Size7⅝ × 2¼ × 3⅝ in (194 × 57 × 92 mm)215 × 65 × 102.5 mm
Mortar joint⅜ in (9.5 mm)10 mm
Per area, single skin6.9 per ft² (≈ 74 per m²)59.3 per m² (≈ 5.5 per ft²)

UK bricks are bigger, so a UK wall uses about 20% fewer bricks for the same area. The brick calculator uses the right brick for each system and works out the mortar.

Concrete blocks differ too: the standard US block is 8 × 8 × 16 in nominal (1.125 per ft²), while the standard UK block is 440 × 215 mm on its face and 100 mm thick (10 per m²). The concrete block calculator handles both.

Tiles, decking and other materials

MaterialUSUK
Common tile sizes12 × 12 in (305 mm), 12 × 24 in300 × 300, 300 × 600, 600 × 600 mm
Deck boards5/4 × 6 (1 × 5½ in), sold per board28–32 × 120–144 mm, often priced per linear metre
Gravel and aggregatesCubic yards or short tonsTonnes, or bulk bags of about 850 kg
Wallpaper rollDouble roll ≈ 20½ in × 33 ft (56 ft²)53 cm × 10.05 m (5.3 m²)
Insulation rated byR-value (e.g. R-49)Thickness and λ value (e.g. 270 mm mineral wool)

A US 12 × 12 in tile is 305 mm — 5 mm bigger than a UK 300 mm tile — which matters when you match tiles to an existing layout. For insulation, US R-values divided by 5.68 give the metric RSI; the UK’s recommended 270 mm of mineral wool is roughly R-35.

Summary

  • Measure in whichever units you like, but buy in the units your store sells.
  • Never convert a product count — convert the area or volume, then divide by the local product size.
  • Watch for the two traps: US vs imperial gallons, and US tons vs metric tonnes.
  • When in doubt, use the coverage or yield printed on the product you are buying.

Calculators for this project