Paver & Patio Slab Calculator

Work out how many pavers, block paving or patio slabs you need for a patio, path or driveway, plus the gravel sub-base and bedding sand or mortar to go underneath.

Calculate pavers or patio slabs

What are you laying?
Measure by
ft m
ft m
in mm
in mm
in mm
0 for pavers with built-in spacers
%
10% for herringbone or curves
in mm
Compacted; deeper for driveways
in mm
$ £

Results

How to use the paver calculator

  1. Choose pavers or block paving (laid on sand) or patio slabs (laid on a mortar bed).
  2. Enter the length and width of the patio, or its total area if it is an irregular shape.
  3. Enter the size of one paver or slab and the joint between them. Most concrete pavers have spacer nibs, so the joint is 0; slabs usually have 8–10 mm (⅜ in) joints.
  4. Set the depth of the compacted sub-base and the bedding layer. The defaults suit a garden patio or path.

The paver formula

Pavers = area ÷ ((length + joint) × (width + joint)) × (1 + extra) Sub-base = area × depth × 1.15 (15% for compaction) Bedding = area × depth × 1.10 (10% for screeding) Mortar = 1 part cement : 4 parts sharp sand

Weights use 2,100 kg/m³ for crushed-stone base and 1,600 kg/m³ for sand. Dry sand and cement bulk up about 27% before mixing, which the mortar figures allow for.

Worked example (US)

A 12 × 10 ft patio is 120 ft². Standard 4 × 8 in pavers need 4.5 per ft², so 540 pavers — 567 with 5% extra. A 4 in gravel base is 40 ft³, or 46 ft³ (1.7 yd³) with 15% for compaction: about 3 tons. A 1 in sand bed is 10 ft³, or 11 ft³ with 10% extra — 22 bags of 0.5 ft³.

Worked example (UK)

A 4 × 3 m patio is 12 m². Block paving at 200 × 100 mm needs 50 per m², so 600 blocks — 630 with 5% extra. A 100 mm MOT Type 1 sub-base is 1.38 m³ with compaction, about 2.9 tonnes (4 bulk bags), and a 40 mm sharp sand bed is about 0.84 tonnes (1 bulk bag). Lay 600 × 600 mm slabs with 10 mm joints instead and you need 34 slabs, with a 40 mm mortar bed of 8 × 25 kg bags of cement and 0.86 tonnes of sharp sand.

Common paver and slab sizes

SizeTypical usePer ft²Per m²
4 × 8 in (100 × 200 mm)Brick pavers, block paving4.550
6 × 6 inSquare pavers443
6 × 9 inInterlocking pavers2.6729
12 × 12 inPatio pavers110.8
24 × 24 in / 600 × 600 mmPatio slabs0.252.7–2.8
450 × 450 mmUK patio slabs0.464.9
900 × 600 mmLarge-format porcelain or stone0.171.9

Figures exclude joints. Wider joints mean slightly fewer slabs, which the calculator allows for.

Base and bedding depths

ProjectSub-baseBedding
Garden path or patio4–6 in (100–150 mm)1 in sand (25–40 mm)
Patio slabs on mortar4 in (100 mm)1–1½ in mortar (25–40 mm)
Driveway8 in+ (150–200 mm+)1 in sand (25–40 mm)

Pouring concrete instead? Use the concrete calculator. For a loose gravel area, the gravel calculator works out the stone.

Planning a whole patio? The patio calculator adds the digging, soil to remove, membrane, jointing sand and edging to the same list.

Frequently asked questions

How many pavers do I need per square foot?

Divide 144 by the paver’s face area in square inches. Standard 4 × 8 in pavers need 4.5 per ft², 6 × 6 in pavers 4 per ft², 6 × 9 in pavers 2.67 per ft² and 12 × 12 in pavers 1 per ft². In the UK, 200 × 100 mm block paving needs 50 blocks per m². Add 5% for cuts, or 10% for herringbone and curved edges.

How much gravel and sand do I need under pavers?

For a patio or path, lay 4–6 inches (100–150 mm) of compacted crushed-stone base — crusher run or ¾-inch minus in the US, MOT Type 1 in the UK — topped with about 1 inch (25–40 mm) of bedding sand. Driveways need a thicker base, typically 8 inches (150–200 mm) or more, and more again on soft clay or where the ground freezes.

Should patio slabs be laid on sand or mortar?

Interlocking pavers and block paving are laid on screeded sharp sand and compacted, so the joints lock them together. Larger patio slabs and natural stone are usually laid on a full bed of mortar — about 4 parts sharp sand to 1 part cement — so they do not rock or sink. Avoid laying slabs on five dabs of mortar, which leaves hollows that crack and collect water.

How much area does a ton of base gravel cover?

A US ton of crushed-stone base (about 2,100 kg/m³) covers roughly 40 ft² at 4 inches deep once compacted. A metric tonne of MOT Type 1 covers about 4 m² at 100 mm. Order 10–20% more than the finished volume, because the base compacts when you roll or plate it.

How much extra paving should I buy?

Allow 5% extra for a simple rectangle in a straight or stretcher bond, and 10–15% for herringbone, diagonal layouts, curves or lots of edges to cut around. Buying all your pavers from the same batch also avoids colour differences between pallets.

Built by Paras Garg and checked by Shivam Sharma and Muskan Gupta. Formulas and figures last reviewed on . Results are estimates: product yields vary, so check manufacturer labels and local building rules before you buy or build. Spotted an error? Tell us.