How to use the wall panelling calculator
- Choose a style. Board and batten is evenly spaced vertical battens with a rail across the top. Grid adds short horizontal pieces between the battens to make squares or rectangles. Shiplap or tongue and groove covers the whole wall with horizontal boards.
- Measure the wall width and the height you want to panel. If you are keeping the skirting or baseboard, measure from the top of it.
- Enter the face width of your battens and the largest gap you would like between them. The calculator chooses the number of battens so all the gaps are equal.
- Enter the length the battens or boards are sold in, then read off what to buy. Add one or two spare lengths for mistakes and damaged ends.
How batten spacing is worked out
With a batten at each end of the wall, there is always one more batten than gap. The calculator finds the fewest gaps that keep each one no wider than your maximum, then shares the space out equally:
Gaps = round up((wall width − batten) ÷ (max gap + batten)) Battens = gaps + 1 Gap = (wall width − battens × batten width) ÷ gaps Vertical = panelling height − rails × batten width
For a grid, each row of squares above the first adds one short horizontal piece in every gap. For shiplap, the number of rows is the height divided by the board’s cover width, rounded up, and the boards are counted from the total length plus waste — or one board per row on short walls, whichever is more.
Worked example (US)
A 12 ft (144 in) wall, panelled to 8 ft with 3½ in battens and gaps of no more than 16 in: (144 − 3.5) ÷ 19.5 = 7.2, so 8 gaps and 9 battens. Each gap is (144 − 9 × 3.5) ÷ 8 = 14 1/16 in. With a top rail, each vertical batten is 96 − 3.5 = 92½ in, so each needs its own 8 ft length; the 12 ft rail takes two lengths joined. That is 11 × 8 ft lengths and 81.4 linear ft in all.
Worked example (UK)
A 3.6 m wall, panelled to 2.4 m with 69 mm MDF strips and gaps of no more than 40 cm: 8 gaps and 9 battens, each gap (3,600 − 9 × 69) ÷ 8 = 372 mm. With a top rail the verticals are 2,331 mm long. Buy 11 × 2.4 m lengths — 24.6 m in total. As a grid three panels high, add 16 short pieces of 372 mm, which come out of three more lengths.
Panelling styles at a glance
| Style | What you buy | Good for |
|---|---|---|
| Board and batten | Vertical battens plus a top rail | Hallways, bedrooms and feature walls; easy first project |
| Grid / square panels | Battens plus short horizontal pieces | Living rooms, dining rooms, headboard walls |
| Shiplap / tongue and groove | Boards covering the whole area | Cottage and coastal looks, bathrooms (moisture-resistant boards) |
| Picture-frame (box) moulding | Moulding cut into frames | Period homes — not covered by this calculator; measure each frame’s perimeter |
Tips for a neat finish
- Plan around sockets and switches. Shift the layout slightly, or the batten width, so a batten does not land half over an outlet.
- Check the wall with a level. Floors and ceilings are rarely straight, so cut the verticals to fit each position rather than all to one length.
- Glue and pin each batten, then fill the nail holes and run decorator’s caulk along every edge — that is what makes it look built-in.
- Paint the whole wall one colour, battens included. The paint calculator works out the paint from the area shown here; allow a little extra for the batten edges.
Frequently asked questions
How far apart should board and batten be?
Most board-and-batten walls have gaps of about 12–24 in (300–600 mm) between battens; 16 in (400 mm) is a popular middle ground. Narrow gaps look busier and more traditional, wide gaps more modern. The calculator picks the number of battens so every gap is equal and no wider than the maximum you enter.
How do I work out the spacing between battens?
Decide roughly how many gaps you want, then: gap = (wall width − number of battens × batten width) ÷ number of gaps. With a batten at each end there is always one more batten than gap. A 144 in wall with nine 3½ in battens has eight gaps of (144 − 31.5) ÷ 8 = 14 1/16 in.
How high should wainscoting or half-wall panelling be?
A common rule is about one-third of the wall height — roughly 32–36 in (800–900 mm) on an 8 ft (2.4 m) wall — or about two-thirds for a bolder look, with a shelf or rail on top. Full-height panelling suits feature walls. Avoid stopping halfway, which tends to look like an accident.
Do I need a bottom rail if I have a skirting board or baseboard?
No. An existing skirting board or baseboard acts as the bottom rail, so leave the bottom rail unticked and start the vertical battens on top of it. Measure the panelling height from the top of the skirting.
What is the cover width of shiplap or tongue-and-groove boards?
It is the width each board adds to the wall once fitted — the full board width minus the overlap or tongue. A nominal 1 × 6 shiplap board covers about 5–5½ in; UK tongue-and-groove cladding often covers about 95–120 mm. Check the product details and use the cover width, not the full width.
What should I use for battens?
Primed MDF strips are the usual choice for painted indoor panelling: they are straight, smooth and cheap. Use pine or poplar boards in damp rooms or where they may get knocked, and moisture-resistant MDF in bathrooms. Fix with panel adhesive and brad nails or pins, then fill and caulk the joints before painting.