Grout Calculator

Find how much grout you need in pounds or kilograms from your tile size, joint width and tile thickness — with the number of bags to buy and how far each bag goes.

Calculate grout for your tiles

Measure by
ft m
ft m
in mm
in mm
in mm
⅛ in = 0.125
in mm
Usually the tile thickness
%

Results

How to use the grout calculator

  1. Enter the size of the tiled area, or its total area if it is an irregular shape.
  2. Enter the length and width of one tile.
  3. Enter the joint width — the gap between tiles, set by your spacers.
  4. Enter the joint depth. Grout fills the joint to nearly the full thickness of the tile, so use the tile thickness.
  5. Keep about 10% extra for grout left in the bucket and on the float, and to have some of the same batch for repairs.

The grout formula

Grout volume = area × (tile length + tile width) ÷ (tile length × tile width) × joint width × joint depth Grout weight = volume × 1.6 kg per litre

Each tile brings one joint along its length and one along its width, so the smaller the tile, the more joint there is in every square foot or metre. Mixed cement-based grout weighs about 1.6 kg per litre (100 lb per cubic foot), the figure grout manufacturers use in their coverage charts.

Worked example (US)

A 10 × 10 ft floor (100 ft²) of 12 × 12 in tiles, ⅜ in thick, with ⅛ in joints needs about 6.5 lb of grout — 7.2 lb with 10% extra. One 10 lb bag is enough.

Worked example (UK)

A 3 × 2.5 m floor (7.5 m²) of 600 × 300 mm tiles, 9 mm thick, with 3 mm joints needs 0.216 kg per m²: 1.62 kg, or 1.78 kg with 10% extra. A 2.5 kg bag is enough, with some left for repairs.

Grout needed for common tile sizes

TileJoint width × depthlb per ft²kg per m²
2 × 2 in mosaic (50 × 50 mm)⅛ in (3 mm) × ¼ in (6 mm)0.2361.15
3 × 6 in subway (75 × 150 mm)1⁄16 in (2 mm) × 5⁄16 in (8 mm)0.1050.51
12 × 12 in (300 × 300 mm)⅛ in (3 mm) × ⅜ in (9 mm)0.0590.29
12 × 24 in (300 × 600 mm)⅛ in (3 mm) × ⅜ in (9 mm)0.0440.22
24 × 24 in (600 × 600 mm)⅛ in (3 mm) × ⅜ in (10 mm)0.0330.16

Before waste. Wider or deeper joints increase the amount in direct proportion: doubling the joint width doubles the grout.

Tips for buying and using grout

  • Buy it all at once. Colour varies slightly between batches, so get enough from the same batch for the whole job.
  • Mix small amounts. Grout starts to stiffen in 20–30 minutes; mix only what you can use in that time.
  • Leave movement joints. Around the edge of the floor and where tiles meet baths, worktops and corners, use a flexible sealant or caulk instead of grout.
  • Seal if needed. Cement-based grout in showers and on floors lasts longer and stains less when sealed, unless the product is sold as stain-resistant.

Still to buy the tiles? The tile calculator works out how many you need, and how to grout tile walks through the job step by step.

Frequently asked questions

How much grout do I need per square foot or square metre?

It depends on the tile size and the joint. For 12 × 12 in tiles with ⅛ in joints, allow about 0.065 lb per ft² — a 10 lb bag covers around 150 ft² and a 25 lb bag around 380 ft². For 600 × 300 mm tiles with 3 mm joints, allow about 0.22 kg per m². Small mosaics can need five times as much, because there are so many more joints.

Should I use sanded or unsanded grout?

Use unsanded grout for joints narrower than ⅛ in (3 mm) and on polished stone or glass that sand could scratch. Use sanded grout for joints of ⅛ in and wider — the sand stops it shrinking and cracking. In the UK, the equivalent choice is between a fine wall grout for joints up to about 3 mm and a flexible wide-joint grout for floors.

How wide should grout lines be?

Rectified porcelain with precise edges can be laid with 1⁄16–⅛ in (2–3 mm) joints. Standard ceramic tiles usually need ⅛–3⁄16 in (3–5 mm), and handmade or quarry tiles more. UK standards recommend a minimum of 2 mm for wall tiles and 3 mm for floor tiles. Never butt tiles tightly together — they need room to move.

How long should I wait before grouting?

Usually 24 hours after fixing the tiles with standard adhesive or thinset, so it has set and the tiles cannot shift. Rapid-setting adhesives can be grouted in 2–4 hours. Check the adhesive’s instructions — large tiles, cold rooms and non-porous surfaces all slow drying.

Does this work for epoxy grout?

Yes, as an estimate. Epoxy grouts have a similar density to cement-based grouts, so the weight is close. Epoxy is sold in kits by weight or volume, and wastage is often higher because it has a short working time — check the coverage chart on the product you choose.

Built by Paras Garg and checked by Shivam Sharma and Muskan Gupta. Formulas and figures last reviewed on . Results are estimates: product yields vary, so check manufacturer labels and local building rules before you buy or build. Spotted an error? Tell us.