Concrete Mix Ratio Calculator

Mixing your own concrete? Enter the size of the job and choose a mix ratio to see how many bags of cement to buy, how much sand and gravel — or all-in ballast — to order, and roughly how much water to add.

Calculate cement, sand and gravel

How much concrete?
ft m
ft m
in cm
%
Aggregate

Results

How to use the concrete mix calculator

  1. Enter the length, width and thickness of the slab, footing or pad — or the volume if you already know it. Not sure of the volume? The concrete calculator works it out for slabs, footings and post holes.
  2. Choose a mix for the job (see the table below) and whether you are buying sand and gravel separately or all-in ballast.
  3. Keep 10% extra for spillage, uneven ground and the concrete left in the mixer.
  4. Read off the bags of cement, the weight of each aggregate to order and a starting amount of water.

Concrete mix ratios

Ratios are parts by volume: cement first, then sand, then gravel. A stronger mix has more cement for the same amount of aggregate.

MixCement : sand : gravelCement : all-in ballastTypical uses
Strong1 : 1½ : 2½1 : 3½Steps, paving, driveways, anything exposed to frost and traffic
General1 : 2 : 31 : 4Slabs, patios, shed and garage bases
Standard1 : 2½ : 3½1 : 5Footings, light wall foundations, setting fence posts

These are the mixes in B&Q’s UK concrete guide and match common US practice. For structural work — house foundations, suspended slabs, retaining walls over about 3 ft (1 m) — follow your engineer’s specification or order concrete to a stated strength instead.

US and UK names for the materials

  • Cement: Portland cement, sold in 94 lb bags in the US and 25 kg bags in the UK.
  • Sand: concrete sand or coarse sand (US); sharp sand or grit sand (UK). Not soft building sand.
  • Gravel: ¾ in crushed stone or gravel (US); 20 mm gravel or aggregate (UK).
  • All-in ballast: sharp sand and gravel already blended — the usual choice for small UK jobs.

How the quantities are worked out

Loose materials take up more room than the concrete they make, because the sand fills the gaps between the stones and the cement fills the gaps between the grains of sand. So the calculator starts from a larger dry volume, then splits it by the ratio:

Dry volume = concrete volume × 1.38 (sand + gravel) = concrete volume × 1.28 (all-in ballast) Each part = dry volume × its share of the ratio Cement bags = cement volume × 1,440 kg/m³ ÷ bag weight Water ≈ cement weight × 0.5

The dry-volume factors come from Tarmac’s published batch for paving concrete (Tarmac makes Blue Circle cement): 2.5 m³ of concrete from 40 × 25 kg bags of cement with 1.0 m³ of damp sand and 1.75 m³ of coarse aggregate — or 2.5 m³ of all-in ballast. Sand and gravel are converted to weight at about 1,600 kg/m³ and ballast at about 1,700 kg/m³; real figures vary with moisture.

Worked example (US)

A 10 × 10 ft slab, 4 inches thick, is 33.3 ft³ (1.23 yd³), or 1.36 yd³ with 10% extra. For a 1:2:3 mix the dry volume is 1.36 × 1.38 = 1.87 yd³, split into six parts: one part cement is 8.4 ft³, so buy 9 × 94 lb bags of Portland cement, plus about 0.84 tons of sand and 1.26 tons of gravel.

Worked example (UK)

A 3 × 3 m base, 100 mm thick, is 0.9 m³, or 0.99 m³ with 10% extra. For a 1:2:3 mix the dry volume is 0.99 × 1.38 = 1.36 m³, split into six parts: about 327 kg of cement — 14 × 25 kg bags — plus 0.73 tonnes of sharp sand and 1.09 tonnes of 20 mm gravel.

With all-in ballast at 1:4 instead, the dry volume is 0.99 × 1.28 = 1.27 m³, split into five parts: 15 bags of cement and 1.72 tonnes of ballast — just over two bulk bags of about 850 kg, so order three or top up with small bags.

Mix your own, buy bags or order ready-mix?

  • Pre-mixed bags are easiest for post holes and small repairs — the concrete calculator counts the bags.
  • Mixing your own from cement and aggregate is cheapest for jobs from a few barrow-loads up to about a cubic yard or 0.75 m³. Our guide on how to mix concrete covers the method step by step.
  • Ready-mixed concrete from a truck is usually better above about a cubic yard, when mixing by hand would take all day and the first batches would set before the last.

Tip: measure every material with the same bucket, and count the buckets. Measuring by shovelfuls is less accurate, because a shovel holds more damp sand than gravel.

Frequently asked questions

What does a 1:2:3 concrete mix mean?

One part cement, two parts sand and three parts gravel (coarse aggregate), measured by volume — usually with the same bucket or shovel for each. It is the most common general-purpose mix for slabs, patios and shed bases.

How many bags of cement are in a cubic metre of concrete?

For a general 1:2:3 mix, about 13–14 × 25 kg bags (roughly 330 kg) per m³ of finished concrete. A strong 1:1.5:2.5 mix needs about 16 bags. In US units, a 1:2:3 mix takes about 6 × 94 lb bags of Portland cement per cubic yard.

What is all-in ballast?

All-in ballast (UK) is sharp sand and gravel already mixed together, so you add only cement and water. Mixes are given as cement to ballast, for example 1:4 or 1:5. In the US the nearest product is a sand-and-gravel “concrete mix” aggregate sold by the ton.

How much water do I add to concrete?

As a guide, about half the cement’s weight in water: roughly 12 litres per 25 kg bag, or 5½ US gallons per 94 lb bag. Damp sand already holds water, so add it gradually and stop when the mix is workable. Extra water makes concrete easier to place but weaker and more likely to crack.

Can I use building sand for concrete?

No. Use sharp sand (UK), also called concrete sand or coarse sand (US). Soft building sand is for mortar: its fine, rounded grains make weak concrete that shrinks and cracks.

Is it cheaper to mix my own concrete than to buy bags?

Usually, yes — loose cement, sand and gravel cost much less per cubic yard or m³ than pre-mixed bags, and you avoid carrying dozens of heavy sacks. For very small jobs, pre-mixed bags are simpler; for large pours, ready-mixed concrete saves a lot of work.

Built by Paras Garg and checked by Shivam Sharma and Muskan Gupta. Formulas and figures last reviewed on . Results are estimates: product yields vary, so check manufacturer labels and local building rules before you buy or build. Spotted an error? Tell us.