How to use the siding calculator
- Add up the length of every wall you are covering and enter the total, with the wall height to the eaves.
- If the building has gable ends — the triangular wall under a pitched roof — enter how many, and the width and height of one.
- Enter the total area of windows and doors to leave out.
- Enter the board length and its exposure: the width that shows once boards are lapped or interlocked.
The siding formula
Wall area = total wall length × wall height Gable area = ½ × gable width × gable height (for each gable) Net area = walls + gables − windows and doors To order = net area × (1 + waste) Squares = area in ft² ÷ 100 Boards = area to order ÷ (board length × exposure)
Worked example (US)
A single-storey house 40 × 30 ft has 140 ft of wall, 9 ft high: 1,260 ft². Two gables 30 ft wide and 7.5 ft high add 225 ft², and windows and doors take off 200 ft², leaving 1,285 ft². With 10% waste that is 1,414 ft² — 14.1 squares. In 12 ft planks with a 7 in exposure (7 ft² each), that is 202 planks.
Worked example (UK)
A garden room with 12 m of wall to clad, 2.4 m high, is 28.8 m². Taking off 4 m² for a door and window leaves 24.8 m², or 27.3 m² with 10% waste. In 3.6 m boards covering 125 mm each, that is 61 boards, or about 218 linear metres.
Typical board sizes
| Material | Typical length | Typical exposure | Sold by |
|---|---|---|---|
| Vinyl siding (US) | 12 ft – 12 ft 6 in | 8–10 in (two 4–5 in laps per panel) | Box of 1 or 2 squares |
| Fibre cement lap siding (US) | 12 ft | 5–7 in (6¼–8¼ in plank) | Plank or square |
| Wood clapboard / bevel (US) | Random, 6–16 ft | 4–7 in | Linear foot |
| Timber cladding (UK) | 3.6–4.8 m | 95–125 mm (125–150 mm board) | Linear metre or m² |
| Composite / fibre cement cladding (UK) | 3.6 m | 130–190 mm | Board |
Sizes vary between products — always use the cover width from the product you are buying.
What else to order
- Trim. Corner posts, J-channel or trim boards around every window and door, and a starter strip along the bottom. Measure these as lengths, not area.
- House wrap or breather membrane for the full wall area, plus overlaps.
- Battens. Timber and composite cladding in the UK is fixed to treated battens, usually at 400–600 mm centres, to leave a ventilated gap behind the boards.
- Fixings. Corrosion-resistant nails or screws — stainless steel for cedar, larch and coastal sites.
Re-roofing at the same time? See the roofing calculator. For paint on cladding, the paint calculator works from the same area; for stain or oil on timber cladding, use the stain calculator.
Frequently asked questions
How do I calculate how much siding I need?
Multiply the total length of the walls by their height, add the gable ends (half the gable’s width × its height for each), and subtract windows and doors. Add about 10% for waste. In the US, divide the result by 100 to get squares — siding is sold by the square, which covers 100 ft².
What is a square of siding?
A square is 100 square feet of coverage. Vinyl siding usually comes in boxes covering 1 or 2 squares. A 1,400 ft² order is 14 squares.
What is the exposure or cover width of a board?
It is the width of each board that actually shows once the boards are overlapped or interlocked — always less than the board’s full width. An 8¼ in fibre cement plank installed with a 1¼ in overlap has a 7 in exposure; a 150 mm cladding board may cover 125–130 mm. Use the exposure, not the full width, to work out how many boards you need.
How much waste should I allow for siding or cladding?
Allow 10% for a simple rectangular building. Allow 15% or more for a house with several gables, dormers or many windows, and for diagonal or vertical board layouts where more offcuts are unusable.
Should I subtract windows and doors?
Subtract large openings such as garage doors, patio doors and picture windows. Many installers do not subtract ordinary windows and doors at all, because the offcuts around them are mostly wasted — if you do subtract them, keep the full 10% waste allowance.